I have a 2921 ISR with a HWIC-4t1/e1 that I am tring to connect to an ATT T1. The circuit was running on an HWIC-1DSU-T1 card, so I know that the circuit is good. When I install the 4 port card I have done the following.
conf t
card type t1 0 ...
I have got a Cisco Switch Model WS-C2960X-24PS-L with Software Version 15.0(2)EX5 here.
I tried to turn off router advertisment with the follwoing command
ipv6 nd ra lifetime 0
I also tried
ip nd ra-lifetime 0
But both versions I found on the net di...
We've recently upgrade from Prime 2.2 to 3.0, and were trying to monitor/configure application/AVC options, but there are none to be found. Is this a special license that I don't have?
I have installed a Prime instance with Version 3.0 in our LAB. I discovered several Devices (Automatioc and manually) and i have full access (SSH and SNMP RW)
The Problem is, that the System will not add an automatic link between two direct connecte...
We have different vlans for different floors and services in our organization & all the vlans are created on core switch (Cisco 3750S). When im pinging any VLAN's gateway in our LAN network I'm getting sporadic latencies <30ms. This has not cause a...
We are looking for ways to utilize Cisco Prime to search for particular command strings and standardize them where possible across multiple platforms of Cisco network architecture.
Hello to all,
This anyone know what is the recommended and stable version for Cisco 2921/k9 version 15 please.
Current version is c2900-universalk9-mz.SPA.150-1.M3.bin
Thank you for the help.
Best regards
Hi all,
i am going to purchase a C1-CISCO4351/K9 router, under subline there is a C1-EGW-200-K9.
May i know what is this part for?
what is mean by 200 DO end points?
Can i buy C1-EGW-100-K9 instead?
how to chose between 100 and 200?/ how to determin...
Hello,
i configured Backup via NFS on my Prime but it won't work.
backup-staging-url nfs://10.xxx.xxx.52:/media/Nfs/staging
repository nfsrepo url nfs://10.xxx.xxx.52:/media/Nfs/storage
prime/admin# backup mybackup repository nfsrepoDO NOT pre...
Lets say, I login to a cisco router via console, telnet or ssh using putty, then entered "telnet 8.8.8.8". While the router is showing/doing "Trying 8.8.8.8...", what is the correct esc sequence to stop that telnet?
I tried Ctrl+Shift+6, Ctrl+Shift+6...
Hi,
I have a question regarding applying configuration on NXOS.
Is there a way to apply a configuration file to running-config so that it will completely replace the old running-config by the new configuration? To be specific, I want the config to ...
Is there a way to view the devices affected by user defined cli config template in job approval? We want to ensure that junior engineers are able to apply user defined cli config template to devices, but then the request goes to job approval. In jo...
I've been wondering what line card is?
Is it like NIC on interface?
Thank you. I'm learning CCNP. Hope I can move on my learning with the help of this community.
I'm trying to create an EEM applet to do automatic tftp backu on my Nexus 7706 running 6.2.12, but I'm not seeing the "event timer cron" option under the created event manager applet. Do I need to create a crom policy to get this to work? Here are ...
Hello, can somebody confirm that PI logs in to the device's CLI via SSH/telnet, types conf t and executes the commands from the tepmlate? Or the proces works differently?
