Hello Friends My company asked me to give a knowledge transfer session for a customer. I have less experience in LMS 4.2. Does anyone have any video, presentation or document ? Thanks and Regards,Abdul Hameed.
Hi, all. So I have a simple EEM script for my 4507 closet switches to poll every minute for high CPU (above 75%), and log it to bootflash:event manager applet HIGH_CPU event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.3.1 get-type exact entry-op ge entry-...
Hi, I found it almost impossible to manage any of the new devices cisco interleaved 6 months in the market.Anyone know if you can manage (create vlan, enabled ports, ports assigned to vlan, enabled ports) on cisco prime infraestructure 2.X switch for...
Hii am running LMS 4.2.4 and i have problems with software distribution.we have about 1000 switches and routers. i receive the error message: "Error loading image to Flash. See C:\PROGRA~2\CSCOpx\files\rme\jobs\swim\5755\sw0-linz-dl35_telnet.log for ...
I need to set up some parameters on SG, SF series switches with snmset command from NET-Snmp tools. It is possible for me to set up some simple parameters like ifAdminStatus of the port. The command to do this looks like:snmpset -m ALL -v 3 -u secNam...
Hi.Our monitoring software draws SNMP graphs from the Cisco 7609 router each minute.When the router gets the BGP Full View from our upstream provider it stops responding to SNMP queries (2-3 minutes downtime)I tried the command:snmp-server priority h...
Customer has a Cisco VG350 voice gateway. They want to send the phone call status to other equipment through the SNMP trap.The equipment should know that if the IP phone is ringing(3) status or not.How could we monitor the 100 IP phones' status at th...
Hi, I would like to control what kind of devices will be managed by DFM.In the "old" LMS 3.2 I was able to add/delete devices to DFM database manually. Now all DCR devices are managed by DFM automatically. How can I control the DFM what kind of devi...
Hello,We are using LMS 4.2 and whenever we select option to reboot the device it fails, if we dont use that check box it works fine.We can go to device and use reload and it works fine with the same user account.Any suggestions?
Hi Can anyone please advise on the below queries 1) New licence is required for migration from 4.0 to 4.0.1? 2)New licence is required for upgrading from 4.0.1 to 4.1? 2) New licence is required for upgrading from 4.1 to 4.2? Please advise Thanks Reg...
Hi Please advise on the below. Thanks in advance.Upgrade Lms from 4.0 to 4.2 1) Licence required for upgrade from 4.0 to 4.0.1? 2)Licence required for upgrade from 4.0.1 to 4.1.x? 3)Licence required for upgrade from 4.1 to 4.2.x? Thanks & Regards
Hi,i have somewhat annoying problem with the monitor config threshold deployment. I want the Cisco Prime to generate an alarm when the traffic utilization on a specific interface goes over 90%. This is pretty straight forward to configure, problem is...
I have an issue with the Prime Infrastructure 2.0 . I would like to use the PI 2.0 to monitor UPS by SNMP . I tried upload the UPS'MIB (Pls,see attachment) to Prime Infrastucture. However it prompts me for the following error message, any id...
Hi all,Here's the scenario...I have two ISPs (L3 and XO) each connected to it's own 3925E. Currently, I'm only receiving the default route from the ISPs. We essentially dedicate our L3 connection for Inbound traffic (e.g. Website hosting) and, the ...
