I setup my ASA5510 with a 3rd Party Certificate for SSL VPN's. How do I go about backing up this certificate if I have to replace the device? I already have a copy of the config. Is that enough? Thanks.
I have the outside interface setup for DHCP that connects to comcast.My inside interface is 192.168.69.1 and is setup to provide DHCP for my internal LAN. I have never logged into a firewall before and as I quickly found out the commands are not lik...
I have an ASA 5505 running v8.03 firmware that after a few days of uptime stops accepting SSH connections.My SSH setup is pretty simple, just:ssh 0.0.0.0 0.0.0.0 outsidessh timeout 60I get the following messages in my syslog when SSH stops working:(y...
I have installed the cisco VMS entprise edition. But whenever i try to configure it, it gave me error of DCR server is not running. Though I have restarted it so many times and even restarted the service but still getting the error. dont know what is...
I am trying to route traffic from 192.168.255.0 /24 to a host 10.213.121.236. The traffic is being killed off by the pix and i can't see why. Does this version PIX Version 6.3(1) allow recognise 192.168.255.0 as a valid network?
Hi, I have mangaged to connect to my Cisco ASA 5520 from the internet via the Cisco VPN client. I just used the ASDM wizard to create this. But I can't connect to any internal servers, or any thing really. I have yet to add any access rules but th...
I need some help with a setup for email.SetupI have a PIX525 and an ASA5510VPN and an internal 2950 router. The PIX does firewalling and the ASA does VPN. Currently all outbound Internet traffic goes through the PIX via the router with this command:i...
PIX Devices Running Versions 6.2 and 6.3"Issue the activation-key command in order to change your activation key if the PIX currently runs versions6.2 or 6.3." Why do I have to do this ? Thx, Peter@it-123.co.uk
Guys.Everytime I try to launch User Tracking, it shows that it failed to connect to the ANIServer.I've tried restarting the ANIServer which didnt work. I even ran reinitdb.pl (with and without the -restore switch),which still failed. Appreciate any h...
I have established a site-to-site tunnel between our two office bldg's, but I'm unable to ping between the two. Both IPSec and IKE negotiate and show active connections, but if I check the IPSec tunnels in the VPN status monitor, there are no decapsu...
Is there a virus update file newer than 11/2005? I can't find one. Build Version: 6.0(3)E1Signature Definition: Signature Update S314.0 2008-01-22 Virus Update V1.2 2005-11-24
I have activated the ARP inspection at FWSM of Cisco 6509. Is there an SNMP MIB to show ARP table info at FWSM of Cisco 6509? The "ipNetToMediaTable" MIB does not return anything.
I am configuring an ASA5520, which is acting as a Certificate server.The CA server is enabled and I have issued some client certificates.I have enabled the following commands:webvpn enable outside ssl certificate-authentication interface outside port...
Hi, ISP--R1--Firewall--R2--R3--Pc(webserver) ISP is terminated in the R1 router.To provide internet for users, Dynamic NATing are given in the rotuer(R1) level itself.R1 F0 ip is primary public ip and Secondary ip is private ip which is terminated ...
Hi all,I need a help with this one.We have configured one our physical interface (X) to be without an IP address and we have created on the same interface the VLAN interfaces (E, F, G, H). But because we have our PIX in failover we observed following...
