My Python Script:from suds.client import Clientwsdl="file:///D:/axlsqltoolkit/schema/current/AXLAPI.wsdl"location = 'https://10.1.9.202:8443/axl/'username="XXXXXX"password="XXXXX"client=Client(wsdl,location=location,username=username,password=passwor...
Forum Posts
Cisco TelePresence MCU 4520 build 6.18(3.42) version 4.4(3.42) is dropping some but not all endpoints at exactly 8min 23sec (see attached screenshot). We are currently migrating to a SIP environment but there is no specific pattern to the call drops....
Hi everyone, IP Phones <-- Alcatel PBX -> E1-QSIG -> ISR 4451 -> MGCP -> CUCM 11.5 (SU2) --> IP Phones I have this topology in my company and I have some problem about "who can call where" ? I want to do this? -2000 in Alcatel side can call ju...
I am able the configure the device and it registers to cucm v 10.5. The registration status changes in about 2 minutes to un-registered. If I reboot the VCS754 it will register to cucm again but, as before, only stays registered about 2 minutes. I ha...
Hello team, Good Afternoon. i got request for a phone where i need to block incoming call, only need to active outbound call so please assist me in best way to do it. The prompt response would be highly appreciated. Thanks a lot. Regards Vi...
Hi all, I try to configure a CUBE to retreive it's information via DHCP. On the DHCP interface Gig 0/0/1 I can't configure: ip dhcp client request sip-server-address What's the prerequesites for this command? best regards Kai
I want to upgrade CUCM 9.x to 11.x. Will this be called upgrade or migration? Kindly let me know do I need to have new license or existing licence could be migrated. If yes, how to do it? I do have valid subscription until 2017.
Greetings, I would like to use SolarWinds NPM 21.0.1 to monitor my CUCM 11.5 cluster. How would I configure NPM and SNMP on the CUCM cluster to make this happen? Any help in this matter is greatly appreciated. Very respectfully.
Resolved! Controlling outbound caller ID in CME
We're running Callmanager Express (CCME) 3.x with a Single PRI to the PSTN. Is it possible to have the CME control outbound caller ID (ANI) when sending calls to the PSTN via the PRI interface? For example, for some extensions (eg conference room) ...
Does anyone have this NM working in a 2811 Router? I have a 2811 running 12.3(11)T3 IPVOICE with the external power supply. I tried several other versions of IOS, same result. The switch ports work fine with workstations, but they will not power t...
Hi All mybe there is an old problem. We have to replace our ISDN FAX connection with SIP Trunk. Design: FAX Server(Kofax) - CUBE(CS-4451 IOS XE Software, Version 16.03.05) - TelkoProvider(Sunrise) Prefered Codec for FAX : G711 aLaw Now we have a prob...
First of all, good afternoon!My name is Jheferson, I use UCCX v11.5 (1) here in the company and am having a hard time with Finesse. When I click on "Team Data" or "Queue Data" the information that should appear does not appear. Can someone help me??
Hi UC Experts, I installed a new CallManager 11.5 version (11.5.1.12900-21).Let the CP-7962 register to CallManager is no problem.But it was problem on the registration of CP-8861 / CP-9971, that showed the error as "Verify Configuration Error"After ...
Hello Everyone, In my office, dont have VoIP lan, i am using DATA wifi on my laptop, in this scenario, Is it possible to install the CIPC on my laptop. Currently, i installed the CIPC and getting this "registration rejected security error", Try to de...
Hi, I'm having issue with ip phone 7821 drop call after Conference call, but when I use ip phone 6921 as SCCP, then I make Conference call and it works. I am making a both conference to pstn, and using same Device Pool and MRGL. I am using CUCM ...
