Other Data Center Subjects

Ask me Anything Webinar: Migration of your Hyperconverged solution

Your Exclusive Ask me Anything webinar on the Migration of your Hyperconverged Solution has landed! Coordinated by our colleagues in the Insider Advocates team and to support customers here in the Cisco Community, Champions, and the Insider Advocat...

Resolved! Nexus 5000 peer has incomplete arp entries despite vpc domain ip arp synchronisation

ip arp difference between both nexus routers (Nexus 56128) despite arp synchronisation in the vpc domain. One marks the arp entry as incomplete whereas the other nexus arp table contains the correct mac address. Any suggestions where this can come fr...

Resolved! 'Command Parsing Failed'

Hi,we have 2 Nexus 5K (cisco Nexus5548 Chassis - System version: 5.1(3)N2(1)).When we are trying to add new vlans to a Portchannel using switch-profile we get this message: Error(s): Following commands failed parsing: If the error is 'Command Parsing...

IEEE 802.1Q-in-Q VLAN Tagging support on Nexus 5548UP ?

Hi,Is Q-in-Q tunneling supported on the N5K platform ? I can not find any document that says it is. I am currently running code version 5.1(3)N1(1) and am not able to configure it.I can however find documents that say it is supported on the N7K platf...

Using ASA as a router

Dears in community I am in search for performance effect of using ASA firewall instead of router for the propose of inter VLAN routeing in enterprise environment (50 VLAN and 1000 User).

Cisco Ftd firepower

already running install cisco sfr ASA FirePOWER Up 5.4.1-211 can we upgrade it

Enable Netflow data to view on Cisco Prime

Can we enable Cisco Prime to collect Netflow Data Send b y network Devices on Cisco Prime 3.2. If yes, then how can we do that. Is this feature required additional licdense?

IP is disabled on Ethernet 1/1

I have a Cisco Nexus 3000 series switch connected to another manufacturer's device. Port Ethernet 1/1 is configured to be in trunking mode. But I am getting a 'IP is disabled on Ethernet 1/1' message from the console port. Additionally, the device...

Nexus Data Broker VM requirements

I've been tasked with deploying NDB ni a centralized configuration, my VM team is asking for disk space requirements and other pertinent details. We'll be using two 9K switch as the aggregators, TBH I'm not sure how many switches we will be gathering...

Data Centre migration plan

Hello In our data center we will be replacing our existing Cisco ASA 5520 active/standby firewall pair with Cisco ASA 2210s and also swapping our 3750G core switch stack with 2 Nexus 3172Ps. We would like to set up the new hardware in parallel with...

Connecting Cisco Nexus 3172T to Juniper QFX5100; will not connect at 10G/full

When connecting cisco nexus 3172T to juniper qfx5100, e.g. [QFX]----xe-1/0/47---------e1/47---[Nexus], they negotiate to 100/half only. With disabling auto negotiation, they connect at 100/full. Is there a way to get them to connect at 10G/full or ...

Change IP address on DCNM OVA

We are running DCNP 10.4.1, deployed via an OVA on VMware. We just moved the VM to our new data center and need to change the IP address, gateway, subnet, and DNS. I have looked at instructions which said to modify installer.properties, but this di...

Networking solution ( networking beginner)

Hello, I'm in my third year as an IT student, I had 2 courses regarding networking, but these courses were just theoretical without any practical application, that's why I'm still confusing many ideas. I've been asked to find a solution to a company,...

Errors found during hypervisor Configuration

Hi Guys, Good Day, I want to share error that we encounter during our installation of Cisco Hyperflex, Can you help identify the cause of this error? Thanks

Appdynamics SaaS

Does anyone know if AppDynamics has a SaaS that can be sold from Cisco or is this just on prem product?

Resolved! Nexus 9500 Max Amperage Consumption

Hello, I want to find information about the max electric current consumption of the Nexus 9500, I have 20 amps destinated for that equipment, I want to know if that is enough? Please send me a URL with that information. Thanks for all the help. R...