Hello,I have 10 CV in my router connected to X25, and i want to dedicat one CV for management (with CiscoWorks or others), can you help me how to configure my interfaceThanks
Hello,I have 10 CV in my router connected to X25, and i want to dedicat one CV for management (with CiscoWorks or others), can you help me how to configure my interfaceThanks
Hi, If I want to start inter-vlan routing on a catalyst 3550. is the following commands enough :3550(config)#ip routing 3550(config)#interface vlan <no> 3550(config-if)#ip address + mask3550(config-if)#no shut Is it still necessary to enable routing...
Hello,I was wondering if you could add 2 ip addresses in a different subnet to 1 VLAN (interface) on the MSFC module.The reason I ask this is because of the fact that I would like to setup a host server with several virtual servers. The host server ...
What does the "remote command" function do ? Can't seem to find it anywhere in CCO , tried the IOS command reference but doesn't find anything and did a search and didn't find anything either . Any pages where I can read about it ??
Can anyone point me to a good PVLAN reference. I know how to configure them and how they work at a high level but I am having difficulty finding any in-depth whitepaper type stuff. Basically I'm looking for something that outlines the inner workings ...
Hi,I don't know what's mean of the command"ip host rund". somebody can tell me?thanks Sincerely
I need to trunk two vlans from a cat6500(catIOS) to a 3725 fastE0/1:10/100 and bridge them across the WAN to another 3725 connected fast0/1:10/100 to a cat6500(nativeIOS). No routing is necessary, since L2 connectivity is the only requirement.What is...
Hi AllGot a tunnel router, with VPN to 10.220.0.0/16 subnet. All works fine. How can I redistribute this into the EIGRP?At the moment, I need to put in a static route on our main site router for ip route 10.220.0.0 255.255.0.0 10.0.1.15 to send data ...
Hi, All.Is it possible to use multilayer switch (like 3550) as router-on-stick?[layer2-only sw w. some vlans]--- dot1Q ---[3550 with ip routing enabled]May it work?Thanx in advance.
Good day.I'm trying to help a friend who lives abroad so I don't have the hands on the hardware.He wanted to use a old 1600 series router as a firewall in a LAN.So the test setup is as follow:-a d-link router for internet connectivity. It has a 4 por...
HI There,Anyone can assist me on WIC-2FXS card,The problem is when I shut the voice port and the FXS is down.IS the any command which can active the WIC-FXS card beside Shut and No Shut ThanksSimForeign Exchange Station 1/1/0 Slot is 1, Sub-unit is 1...
i have a cisco 2600 router, and i wantd to add a WIC-2t interface card but a don´t know what type of card is, if spare or smart serial, how i can know?
hiplease check the attached network diagram.this is my setup.how can i encrypt the data flowing from one network to another,IOs supports encryption.my router connects to 12 diff locations using e1 links so i want to implement encryption on routers ....
Has anyone heard of a problem with pointing a static route to an out going sub-interface? I have a client with a 7204VXR with an ATM port adapter (PA-A3-OC3SMI) configured with sub-interfaces. The static route looks like this (for example): ip rout...
I have a 3725 and have 2 - VWIC-2MFT-T1's. Trying to configure MFR. When I go to setup the mfr interface (int mfr1) I get a invalid input detected. The commad is there when I type int ?. Running IOS 12.2(15)T14. Any help would greatly be appreciated.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |