do AS-PATH prepends affect *all* routes advertised or can prepends be applied on a per route basis using BGP v4 ?
do AS-PATH prepends affect *all* routes advertised or can prepends be applied on a per route basis using BGP v4 ?
After the PPPoE negotiation was completed,two addresses connected in Dialer can be found on the routing table.(like the following) 192.168.1.0/32 is subnetted, 2 subnetsC 192.168.1.1 is directly connected, Dialer1C 192.168.1.240 is di...
Hi - Can someone enlighten me. I need a process whereby I would like to migrate away from static routes, in the core and edge routers, to a dynamic routing algorithm. Any suggestions? Many thanks
Help!!I made a terrible mistake on my 2611xm router.I had issue command "confreg 10000" with a wrong parameter in the rommon,then i reset the router,there's no response in the terminal.The router couldn't boot normally.The hotkey "ctrl+break" couldn'...
I can't open my config...the nvram mem has no free memory...What do i do?736 bytes total (0 bytes free)Directory of nvram:/%Error opening nvram:/ (Device or resource busy)413676 bytes total (410404 bytes free)Directory of system:/
I'm configuring a Cat 4006 and a 2600 router. I enable a trunk on the 4006. And on the router I made a sub interface. since the I get a packet lose or at lease it looks like it. The connection is very slow. Did a ping test and it looks like I lose 1/...
HI I HAVE A 3745 ROUTER WITH 3 VWIC-2MFT-E1 CARDS INSTALLED ON SLOT0, AND 3 2NM-CE1T1-PRI CARDS INSTALLED ON SLOT1 SLOT2 AND SLOT3. AFTER GIVING ROUTER(CONFIG)#CARD TYPE E1 1 ROUTER(CONFIG)#CARD TYPE E1 2 ROUTER(CONFIG)#CARD TYPE E1 3 ALL THE 2NM-CE1...
Wired properly, does CAT 5 Ethernet cable meet specs to provide the connection between the Telco access point and my router interface (U connection)?
I've heard both ways, to use or not to use Auto on the switchports.1. Use 100Full on the switch and Auto on the computer because if both are set Auto sometimes the negotiation goes wrong. With this configuration the computer will chose 100Full since ...
Hi folks,I saw a message regrading the ping command:64 bytes from 16.40.2.1: icmp_seq=372. time=5 ms64 bytes from 16.40.2.1: icmp_seq=373. time=5 ms64 bytes from 16.40.2.1: icmp_seq=374. time=4 ms64 bytes from 16.40.2.1: icmp_seq=375. time=5 msping: ...
I'm writing some scripts do stuff like search my switches for a MAC and to make changes to ports VLAN assignments. I need to know the MIB and OID/pnumonic (if there is one) to tell me whether a switch port is configured to be a trunking port (whether...
Our frame-relay connections between sites consistently perform at 235/255. Is there a way to decifer what traffic that is taking up the bandwidth?Thank you,jp
what are the possible caused of the Multilink PPP ( multilink group ) interface come to be down?Anyone know ?, share your idea with us
3 Building are interconnected to each other and all the out going traffic is from Building A. EIGRP has been implemented in the whole network. Building A has a 2 mbps lease link. Now Building B has become the corporate office and want all the traffic...
Hi friend. I have a Catalyst 3500XL. When I have a trouble on the network, I use to use "show interface.." for seeing if something is wrong. I have noticed a lot of "OUTPUT BUFFER FAILURES" on almost all the fastethernet interfaces. And there are ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
01-22-2025 07:00 AM | ||
12-30-2024 06:12 PM | ||
11-14-2024 09:33 AM | ||
10-24-2024 11:51 PM | ||
10-20-2024 10:52 PM |