Other Network Architecture Subjects

In a mix of 4507 (core) 4506 swithces and 3550 switches, I want to be able to make class c vlans on entire 3550's (or part) only able to get to the internet. What's a simple method? Send all their ip packets to a default gateway on a firewall. But ...

I am wondering how to get my EIGRP routing table to activly use the feasible successor routes in an equal load sharing manner. I have 3 networks in question here 192.168.1.0, 192.168.2.0, 192.168.10.0. Router a is 192.168.2.0 Router b is 192.168.1....

hi ,could anyone tell me what does this route means??ip route 172.19.80.0 255.255.240.0 null0also , would appreciate if anyone could brief me what is null0 relevance and what are its best usage parameters.

I plan to use this configuration:CISCO2611XM Dual 10/100 Ethernet Router w/ Cisco IOS IPS26CP-12208T= Cisco 2600 Series IOS IP PLUSNM-2V= Two-Slot Voice/fax Network Module-SpareVIC-4FXS/DID= 4 port FXS or DID VICWIC-1T= 1-Port Serial WAN Interface Ca...

I'm having an interesting issue with my DSL connection and dynamic IP numbers. I have checked with both the DSL providers (Qwest) and my local ISP, and neither has any answers, which leaves me with router. Perhaps someone here will be able to help....

The requirement is that client wants to have read write access to files on Windows NT box that is on the other side of WAN. He shud be able to edit the files .. the size of files shud be 1-5 MB. Need to know how much bandwidth is reqd per session? Is...

Is there a way to change the telnet password on a cat 6500 with catos 7.4.3 if you know the snmp read-write string ? If so how ? We normally change this thru ciscoworks but it fails saying the password is wrong . We then tried to doing it...

Currently we are using on Core 6509CAT OS : cat6000-sup2 k9.7-3-1.bin SUP Module : WS-X6K-SUP2-2GE,other modules : WS-X6416-GBIC / WS-X6348-RJ-45 MSFC : WS-F6K-MSFC2and on Access Layer we are using Catalyst 4006.CATOS : cat4000-k9.7-3-1.binSUP Modul...

Is there a way to change the telnet password on a cat 6500 with catos 7.4.3 if you know the snmp read-write string ? If so how ? We normally change this thru ciscoworks but it fails saying the password is wrong . We then tried to doing it from the CL...

Is there a way to configure a terminal server (3660) line to ignore a reboot, that is, to not disconnect? The problem is that by the time you log back in, boot-up messages are lost. This is particularly a problem with Unix based servers.

Hi all,I have one question specific to OSPF controlled router shutdown.In ISIS we can take a router out for maintenance purpose by setting set overload bit command. Is there anything similar command or method existing for OSPF? which allows to take t...

Hi guys,I read an input (article) on the above subject in the latest edition of packet and I must tell you that is what I have been looking for.I tried the config on my 1751-V router with IOS 12.3(9a)The IOS is a an Enterprise base (c1700-entbase-mz....

Hi all,The EssentialsDbMonitor and CmfDb monitor failed to run after I installed RME3.5. Tried to start them and got the following error message:{EssentialsDbMonitor}: Cannot connect to 'rme' database, please contact your system administrator.Also, t...

Hello,I'm having a problem with a catalyst 2950 switch ,when i try to paste an access list to the swich getting the following error " %Error: The field sets of all the ACEs in an ACL should match "The IOS ver 12.1Please note that the same access list...