Resolved! 4500 module
Can I use a WS-X4418-GB (for 4507) to connect 3550's at access level?
Can I use a WS-X4418-GB (for 4507) to connect 3550's at access level?
Hi,I have to change our coreswitches from 4003 (Cat-IOS) to 4506 (IOS). On the new switches the ifindexes are different than before.My simple question is how to change these ifindexes?I looked up the Cisco pages but I have not had any success yet.Tha...
Does anyone know how old the CiscoPro Workgroup switch is, model number CPW2115?TIA...
On a 2500 series router can traffic from a subnet be redirected to another gateway or another box. In linux, traffic from one subnet can be redirected to another address or gateway besides the one bounding for the internet. I there such abilities i...
hello,i'm looking for a list or a white paper where all the funny little output details of the show int * command are listet and explained. for some proactive management project i'm also looking for some hints what counters or stats should be or must...
Hi, I currently have RWAN/LMS 2.2 installed on one host. I would like to separate DFM & Fault History to another server. Few questions1) What's the best way to do this. Just uninstall DFM and Fault History? Is there any way I can preserve my existing...
Who knows which PIM control messages are used by SM or DM.I think the followinbg is correct:Graft/Graft-ack is used by DMJoin/Prune is used by SM and DMRegister/Register-stop by SMAssert by DMHello by bothCan anyone verify this?Thanks
I have recently started implementing VLANs at my site with a main 6509 switch going out to 20 2950 switches in the closets. The VLANs are working fine except I don't know how to set up a trunk on 2950s that are in a cluster. The cluster commander w...
Hello peopleI would like to know if someone already use the " set port security auto-configure" in enable mode on the 6513 CatOs 8.2 paltform. I planning to use this feature, but the switches are working with some critical servers connected and I aff...
Hi all,I have catalyst 6509 and I've got a message belows.The clock B is FAIL. How can I fix up the problem ?Hardware replacement is the only solution ?6509_1>> (enable) show environment Environmental Status (. = Pass, F = Fail, U = Unknown, N = Not ...
I installed RME in the network. Most switches are Cat3500XL or Cat3550 switches. When I want to download the software image from the devices to RME to crease baseline, there is no image available. I use "Add image" and "From Network", then neither "I...
I have a cisco 827 connected to telefonica ADSL provider using pppoe.Each time I open the router I get a different ip address, so I have been unable to create a correct Nat translation to be able to use the ADSL connection with all the computers I ha...
My customer has a network of BPX and MGX switches using the MGX8850 with VISM in AAL2 trunking mode for transport of GSM voice traffic in a mobile voice network. Normal vice calls are working fine and the quality is good, however on voice mail retrev...
Hey guyz need some major help hear .... I need RouterA to inject a default route ONLY to Routers B,C and DWhile routers B,C and D advertise connected subnets into Area0 for other areas..... Any ideas ??? [Existing Core Router-7513(Area 0) with 10 si...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |