I have recently installed a new VPN3030 concentrator. I can create a VPN tunnel to the LAN; but I unable to connect to any servers, or ping/trace route any LAN IP address.How do I route the VPN client back to the VPN3030?
I have recently installed a new VPN3030 concentrator. I can create a VPN tunnel to the LAN; but I unable to connect to any servers, or ping/trace route any LAN IP address.How do I route the VPN client back to the VPN3030?
Hi,I have a few questions on the usage of ACL Manager ver 1.6 in Ciscoworks:1. I have configured an ACL and apply on interface E1 in a 2514 router from the console and I can see that it is being reflected in the "Out-Of-Band Change" folder in ACLM 1....
I have a 2611-xm with a 1ce1u ,and it is used as a access server , my config is right .there are some message " rx -> bad frame (0x0000) " when I try to dial the server use a bri .I have changed the 1ce1u ,but the message display again .plase tell ...
HI brief overview 2 x Cat 4006 switches with supp II and 4232-l3 modules connected to 36 Cat 3524XL-en Access switches over Gbic fibre.Trunk links configured with udld aggressive mode set globally on 4006 switches & mod/port access switches also aggr...
Hello! I have Cisco MGC Node Manager 2.4 over CEMF 3.2. I've successfully deployed MGC nodes and BAMS, I see Dialplan/Signalling/Trunking components for each MGC Node and I've set up polling for MGC nodes and BAMS. Now what I want is to run Performan...
Hi can someone please advise on how to verify if a router has sufficient memory to take a full internet routing table.I know you need at least 128M RAM, but when i do a " show version " i am unsure how to interpret all the different memory figures.Th...
I have two Cisco 2620 routers with 2-T1 cards. It uses point to point T1's. Originally it was configured as a bridge, but we are changing it to work as a router. I have reconfigured it, but do not know how to load balance, or if this configuration i...
On a 4500 Switch I am using autoqos on all of my shared phone/pc ports.Upon enabling AutoQos configuration the following parameters come on be default within my individual ports;priority highshape percent 33"shape percent 33"....does that just make t...
I have Ciscoworks2000 running correctly. I also have nGenius RMT1.4 installed, although it has been used from the same server before. I have installed it on other drive, reason lacking of space on C. With different passwords, all changed.The issue I...
While trying to perform a simple IOS upgrade via Ciscoworks I keep receiveing the following error;Error Info Code: '4301' Message: 'Device Error: Cannot perform flash operation.' Action/Reason: 'Probable Cause: Cannot obtain ...
Hi,I inherited managing our network. My knowledge of Cisco is pretty limited but growing. I need help configuring a failover from our T1 to a wireless broadband connection. We have a Cisco 2651 for external, a Cisco 2610 internal, and a PIX in betwee...
I don't usually have to make changes to our cisco routers, but we are moving a bootp server on our frame relay network and the company that usually provides support is unavailable. I think I know what needs to be done, but I want to make sure before...
I must upgrade Catalyst 5500 memory from 32Mb to 64Mb DRAM. Currently it has redundant 32Mb DRAM supervisor III (ws-x5530) w/NFFC II (ws-f5531a). Without powering down the switch, I plan to remove the standby supervisor in slot 2, remove old memory...
Hi Experts,One quick question. ( I hope this is easy). I would like to be able to load balance internet traffic on a Cisco 2621XM running IOS version 12.2(8)T5. My goal is the following:Send 75% through 1 ISP and 25% to a second ISP.What would be ...
How good is Fault History , os is there any other tool that is similar to fault historyunder DFM
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |