Can LAN interface of the 575-LRE attach a switch?
Can LAN interface of the 575-LRE attach a switch?
Is there any way to implement something that works the same way as fremerelay end-to-end keepalive over an ethernet wideband ip connection.the problem that i am having is that the service provider supplys this connection on switches so we basically h...
I have two Cisco 4503 switches with Sup IIIs running 12.1(20) enhanced. They are dual connected to each other. A show standby shows the correct information i.e. that one is active and one is standby. However when I power off the active router the sta...
Can anyone identify for me what the values of 1 and 8 correspond to in the cdeTrapCircuitUpDown trap? I know one should be "connected" and one should be "disconnected", but don't know which is which.TIA for any help.
Hi, thereI have a cisco 2611 router, I would like to use it as my office NAT box.Does anyone know that how many concurrent IPsec VPN sessions and PPTP sessions can pass it when i use cisco router as nat box.where can i find out this kind of informati...
Our campus had an outage and we are trying to find the cause. Something caused all 40 of our 2950 devices fibre uplinks and most of the stacking GBIC's to go in to err-disable mode and not recover. It was NOT just a local event. This outage spanned a...
I am trying to figure out how does the service password-encryption command work. Supposedly, if this command is set, it will enable the password encryption. On the other hand, the password encryption is also available in the "enable password" command...
Has any one been able to multilink or bundle multiple adsl wics on a cisco 3640?
I am trying to work on the input errors and CRCs on the second interface below. The only difference I can see is the queueing strategy and the autovc creation on the second interface. The IOS for the top router is 12.2(8)T5 and the second one is 12.3...
Dear all: I use "show sdm prefer" on 3750-24TS with EMI IOS, and I got: ".... 8 routed interfaces and 1024 VLANs." What's the mean "8 routed interfaces" here? It means only 8 routed port (no switchport) I could use on it or "routed ...
Does anyone know if there is any documentation to interpret the output of 'debug atm errors'I am specifically interested in bad sap messages on IOS 12.2(8)T10.The standard ios documentation link contains only how to turn this command on and off.
Hi,I must to terminate 60 8E1 IMA (60x8E1) to a datacenter.if all of lines are multiplexed to two STM-4 , how can demultiplex them into one switch/router? by which modules?I would be appreciate if you advice me.Regards,M.A.Rad
Hello, In the following scenario, can anyone tell me what decision will be made by the router? server-->CAT4000(layer3)-->3620-->to 172.16.x.xThe cat4000 has a static route to the 172.16.x.x network via the 3620 and a default route out to a PIX firew...
Greetings, What other servers does SLB support? I know it supports HTTP, DNS and FTP servers. But can it support file servers (Novell or MS)?Thanks, Nabil
The GBIC interface is transmiting and receiving high brocast and multicast. The link goes on and off in an average interval of 45mins.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-23-2024 09:00 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM |