Does anyone knows the maximum performance of the FEIP and the FEIP2-DSW on the 7500. I'm trying to compare the performace of the PA2FETX and the FEIPs. Does anyone has any info or links.Thank you
Is the Catalyst 6000 Supervisor IOS affected by the recently discovered vulerability outlined in the following document?http://www.cisco.com/warp/public/707/cisco-sa-20030717-blocked.shtml I noticed that in the main IOS download area, the vulnerable ...
Hi,I have been trying to find Technical Specs for WIC-1B-U-V2 at CCO. My queries and searches didnt yeild any results. Would greatly appreciate if you could help me find the tech specs for WIC-1B-U-V2.Thank you,Ravinda - ravindam@sg.ibm.com
Currently, all my computers are in one vlan pointing to my router for their default gateway (i.e. 172.16.0.1 /16) Correct me if I am wrong, but after I set up Vlans and assign ports to them, I will need to make sure that the default-gateway of the no...
Hi all,we have a small 837 that had all files/memories erased by its previous ownerand while trying to recover it they uploaded the wrong ROMMON file. (I think it was a 827 ROMMON) Nowwhen restarting it says it is an unkown device with 4MB of memory ...
I needed to upgrade my 2 x MSFC2's to c6msfc2-dsv-mz.121-19.E1.bin from c6msfc2-is-mz.121-3a.E4.I copied the new image to sup-slot0:, added the boot system variable and reset the MSFC's from CatOS - they booted the new image from sup-slot0: succesful...
Sir,My router GSR popped out warning message Continually:"%LC-3-PSALOADSHARE: MPLS loadsharing inconsistency for 219.72.0.0/16 ti 1 ld 16"I have no idea about it. And per Cisco Error message decode result, there are 2 solution about it:1) Recommended...
I currently have a Cisco 677 in a default configuration where theserver is at 192.168.1.2 and the other machines on the LAN get to theInternet via NAT. We now have been assigned another IP set (4 IPs, 1allocateable to a machine). The new IP was neede...
Hi!I have a Cisco 6509 with IOS version 12.1(13)E. I would like to know how can get SNMP statistics for every fastethetnet port on every module?I found some documentation about subinterfaces but it seems that this version of IOS does not support subi...
Is there a limit on the number of switches that can be daisy – chained ?I have (2) 4006 switches at the core of our LAN – we use 3548 XL switches in the closets which are trunked vis gigabit interfaces to the 2 4006 switches can I do the followingCor...
Hello , Why Cisco Works cannot monitor private addresses ? When i try to start monitoring i see the following message: Status 11018 Invalid Address. Is there a way to use Cisco works with private addresses ? Thanks fo supprting me
Hello,I have two questions here on the above.Are PIM joins sent multicast or unicast. Some docs says it's unicast, but I see it as multicast in my trace.Also, If a flow maintains state for a period of time, do PIM-Join messages get sent periodically...
We need to download ios to cisco 2620 router via xmodem.We write the command :rommon 7 > xmodem -cr c2600-i-mz.123-1.binDo not start the sending program yet...Invoke this application only for disaster recovery.Do you wish to continue? y/n [n]: yRea...
i want options as to what IOS i should upgrade to there is a total of about 150 routers and 100 switches.The Core is built with 7200's that are running enterprise 122-12a ... these routers have enough memory to upgrade to either 12.2.17a or 12.3.1aTh...
