I need to configure 801 router on leased Line ISDN. Can any one give me the link on cisco website where the commands and configurations examples are postedbest regards
I need to configure 801 router on leased Line ISDN. Can any one give me the link on cisco website where the commands and configurations examples are postedbest regards
Can I have two VLANs with the same name but with differents numbers in a VTP Domain?
We have a Paradyne 9580 that is converting from an MCI ATM network to frame-relay on a Cisco 7200 Hssi port. The other end connects the MCI ATM network directly into a native ATM card on another 7200 (PA-A3 card).The Paradyne is using 'transparent'...
IOS is c3660-p-mz-122-2.T.binIt's a known bug id. CSCdy01451.%CONTROLLER-2-FIRMWARE: Controller E1 4/1, firmware is not running%CONTROLLER-2-FIRMWARE: Controller E1 4/0, firmware is not running%CONTROLLER-2-FIRMWARE: Controller E1 4/1, firmware is no...
I'm new to VLAN configuration but I understand the tecnology. I have 4 cisco 2900XL series and 3, 1900 series. The network experience slow throughput intermitently. The only configuration on the switches is just IP address config. for management purp...
I have a small Vlan network with 1 6509 and 100 + 3524 switches.. My question is if there are some 3534s setup to be VTP server instead of client would it cause problems with my network.?
How can I modify the DFM MailNotifier to send the value of the instance which triggered the event?Normally only the event can be seen in the email and the value not.Eg: I received the following:InCharge Domain : DFM Port PORT-c3550-01/1.2 [Gi0/2] H...
Can any one let me know the command relevant to changing the default arp refresh interval in cisco Routers.Rgdssrini
Added a WIC1ADSL to a 2FE2W (slot 0/0) in a 3640 and turned it on, butthe IOS complained about not supporting the card, so I switched to IOS (tm) 3600 Software (C3640-I-M), Version 12.2(4)T1, which seemsto be about the only choice for the limited fl...
This is the problem:1. I have a 4500 router thats been flashed with 2600 IOS2. I need to do password recovery.Issue at hand. After reading through the site, the recommendation is to boot from ROM (which has the correct IOS image) to deal with the fl...
I am getting approximately 150 ALIGN-ERR and FCS-ERR/minute on a Cat 5000 port that connects to a email server with a 100 MB card. The switch port is hard coded to 100 MB, full-duplex.Is this normal? If not, any ideas where to start fixing this?Tha...
Does any body know how shut down and up Frame Relay sub-interface via SNMP?Show me a sample, please.
Can you forward udp broadcasts to a subnet (rather than a host) using the ip helper-address command?I have an application that relies on UDP broadcasts on UDP port 6614. I want these broadcasts to go to any device on a certain subnet (the subnet is ...
The command 'set logout <time>' for the CatOS (please see the link below) did not clearly mention if this command also applies for the console port. Can anybody confirm if this command applies to both console and telnet idle sessions?http://www.cisco...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-23-2024 09:00 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM |