Hie allCould someone please tell me if the new 3745 can support the Wic-1/2ENET wan interface card, I know it comes standard with 2 fixed FE ports but I need 4 ethernet ports.ThanksRgdsTongesai
Hie allCould someone please tell me if the new 3745 can support the Wic-1/2ENET wan interface card, I know it comes standard with 2 fixed FE ports but I need 4 ethernet ports.ThanksRgdsTongesai
Hi all,I have a 2620 router, with default flash and DRAM. Very simple config with only a WIC-1T serial card. This router serves as an Internet access edge router, and is directly connected to the Internet edge router through a point-to-point 512Kbps ...
While paractising the LAB consisting of four routers and 1900 switches, I cannot ping any remote router from the switch. I can only ping directly connected router with the LAN through ethernet interface. Can that remote router not be pinged from the ...
I've noticed that the line protocol on my Frame Realy HSSI physical interface stays down after a fault condition has been restored. A "shut - no shut" of the interface brings it back up which is something I've noticed with Ethernets before. Is ther...
Does somebody say me what I have to enter on console of Catalyst 8540 to see the exactly type of modules which are installed as route processor,switch processor and other card modules?With "show hardware" I can't understand all this.Where can I find ...
Hello colleagues,I am having a problem installing QPM version3.0. For some reason, after the installation I do not see the program group, so I cannot start QPM. Has anybody experienced this problem ? What is the executable that starts QPM ? After the...
I've had a couple of goes at getting this config correct and am running out of chances. Before I test this in the real world, I'd appreciate it if someone could tell me whether this looks as though it will work. It is an ISDN hub router simply recei...
Hi everyone, my company is constructing a new building and one of the action items is to determine the IP addressing scheme. The building has 4 floors with approximately 100 people per floor. My first inkling was to use a single class C network per f...
Hello,I have now the following error:22:47:24 NETWORK_PORT_SATELLITE PHY_LOCKUP (Repeated PHY Lookup seen on Interface FastEthernet fa 0/2. Interface will be shut down)22:47:26 LINK CHANGED (Interface FastEthernet fa 0/2, change state to administr...
I've just downloaded the file c3550-i9q3l2-mz.121-13.EA1a.bin which is described as the SMI image for the 3550. However, when loaded, "show ver" shows this new image file is loaded but is running the L2/L3 switching image, which is what I would expec...
Is there any thing,that limits the maximun Number of acl's on the 7600 router apart from the numbering of the standard, extended acl's and the 31 character limit to named acl's?regards
I can't seem to find Cisco 11050 mibs and traps. Any ideas?
I am running port security on my cat 4000 and am having problems with 1 port. The violation code set up on the port is 'shutdown'. The port keeps shutting down. I have tried disabling port security and doing a 'clear port security all' on the port to...
I have a small network consisting of about 12 segments 3 WAN connections and access to the Internet over T1. I have several routers with in my LAN that support various functions and system. All act as gateways to different networking systems.I perf...
I have remote location connected to our corporate location with a 256K frame relay pipe. The router at the remote location is a older cisco 1600. I also have a DSL connected to a Cisco PIX 501, connected (when the tunnel is up) back to a Cisco VPN...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |