Other Network Architecture Subjects

DFM Install Doco reads:If you use the RME Adapter to synchronize the DFM inventory with a list of Essentials devices, and the synchronization causes DFM to exceed this limit, the Essentials device list will be truncatedHas anyone seen this behaviour?...

We lost connectivity to Catalyst 4006-SUP3 IOS 12.1-12c.EW1 and we got these errors messages when issued sh logg on cat 4006 (LINECARDMGMTPROTOCOL-4-ONGOINGTIMEOUTWARNING is it a hardware or software problem??):=======================================...

I hav a cat6509 reporting the errors below and can pinpoint a problem. Could it be a bogus error ?OS (tm) c6sup2_rp Software (c6sup2_rp-JS-M), Version 12.1(13)EApr 28 20:15:02: %MLS_STAT-DFC6-4-IP_CSUM_ERR: IP checksum errorsApr 28 20:46:02: %MLS_STA...

I have a couple of questions:1. Can VHM monitor AS4 Analog gateways?I have a site that has 3 AS4-FXS gateways and 2 DT24+ Gateways. When I discovered the CM, it brought back the info all all the gateways but it seems to think that the AS4 Gateways...

When I put "boot host tftp...." in our router config, will the router pull the config from the tftp server (if it can find it), or does it try NVRAM? The docs imply that it will load from the tftp server, but I'm being told otherwise by individuals.

Hi,I have multiple IPsec VPNs from my office to partner location. The way i monitor the connectivity to the partner locations is by doing a ping to some machine in the partner network. But this method is not always reliable as the ping could fail bec...

We need a replacement for our RAS server which is an old Shiva box.We have various third party people dialling in (approx.200) and again have various connections ISDN,Frame Relay and PSTN.A company have suggested a Cisco 3660 router - is this the bes...

Hello,In a frame relay WAN (star topology, RIP and all the remote sites in the same WAN network), which do you think is the best manner of monitoring lines failures?Should we uses a polling solution (pinging periodically every remote)?Is there any tr...

Hello, I would like to know if anybody has implemented SNMP v3 within their network and if you would be willing to share some Do's/Dont's of it...Thanks,Jim

Hello,I have been trying to get my 2514 working but Im stuck. I have a 2514 connected to internet and a small lan. I can ping my outside router ip from my lan but I cant ping my outside gateway. The router is not forwarding past the outside eth0. Her...

I am running a EIGRP network with the 2 central routers running HSRP across their lan interfaces. The primary router redistributes static routes defined on this router into EIGRP. However if this router fails and the backup router takes over within...

I have a 3640 with 16 meg System Flash and 16 meg PCMCIA Flash Slot0:What I want to know is - Can I combine 16M system flash and 16M PCMCIA flash to have a single combined 32M of boot flash aka a single 32 meg partition.Searched CCO and other sites t...

Hi!I have a cisco 2610 configured with ios Version 12.2(10a) (c2600-is-mz.122-10a.bin). 64K DRAM 16K FLASHI have installed a channelized E1 (channel 16 is for in-band signalling).controller E1 1/0 framing NO-CRC4 line-termination 75-ohm channel-gro...

We have a FE-2CE1-B/U module in a Cisco 3620.We use the Router as a access-server. Connected clients lose sporadically the connection. Also the lines are sometimes busy without any client connected.We think we must configure the module in balanced mo...

hello I tried to configure bandwidth remaining percent 30 on the class qiye under Policy-map test,but it notify me that " bandwith should be consistent units",my ios version is c3600-12.2(15)T with JS feature.Please help me solve this problem.Than...