Hi,Can I do EGRESS rate-limiting on a FE trunk port on a 3550 ? I don't care about VLANs, I want to rate-limit specific traffic (DSCPs) no matter which VLAN it is in.Is this supported ?Tx,Frank
Hi,Can I do EGRESS rate-limiting on a FE trunk port on a 3550 ? I don't care about VLANs, I want to rate-limit specific traffic (DSCPs) no matter which VLAN it is in.Is this supported ?Tx,Frank
I have been using the bandwidth command, but it appears ineffective. File transfer speeds are consistently about 50kbps regardless of the speed I set using the bandwidth command.thanks,
hello,we have a catalyst 6500 with a routing module as our backbone switch, I'm willing to use a sniffer (realSecure) to monitor the network traffic and find any suspicios packets beffore it affects our network.The question is: how does it affect the...
Hello all,I am in the process of implementing time based dial on demand routing for a couple of routers running over isdn and i have the following problem?I am basically stopping traffic on several ports bringing up an isdn line for a set period of ...
deal all,i have two 2 mb link connected between my HO and BR. i do have two 2600 routers each side and they are connected to a central catalyst switch on both side. each link is connected to separate set of routers.currently i am using only one link...
hello,whats the entry level switch which is capable of server load balancing..thanks
I have 2 offices connected using 1720 routers with 2 t/1's connected to each router. I would like to utilize both t/1's bandwidth. It seems as only 1 t/1 as used at a time. Config below:Router Ae0 ip address 192.168.71.1 255.255.255.0s0 ip address 19...
I have a 2948G and 2 firewall connect to it,the 2 firewall need multicast communication to backup eath other.but it seems 2948G cann't support,even a hub can do it. the 2948G have default configuration.
Hello, im trying to set-up a netconfig Job, i am defining a ad hoc job a simple access-list amendment i cna define the job and apply it to a templete but when i click next i get lots of Java errors, i have only come across this in Netconfig nothing e...
Hello,I have four 2610 routers going in connected by private T1's. What ip address structure do you recomend I use for the T1 side of the router? I was thinking of using 10.0.1.1, 10.0.2.1, 10.0.3.1, 10.0.4.1 but when I put this config into the conf...
Scenario:ISP1(AS1)|||MYNETWORK(AS4)>>>>>>ISP2(AS2)|||ISP3(AS3)I have two routers, R1 is connected to ISP1 and ISP2, R2 is connected to ISP3. I advertise 192.168.0.0/16 and 172.16.0.0/12 to ISP1 and ISP2, but I only advertise 192.168.0.0/16 to ISP3 (...
This is my first "big" lanI have a little more 200 nodes in my networkI plan use 5 2950G-48 EI with GigaStack connection to 3508G switch.And I have 1 LAN segment on a distance more than 100 m with 20 nodes (2950G-24EI) . I plan to connect that se...
Hi All,I face the problem with my L3 module of Catalyst 4006 switch. When I issue "show run", nothing comes out. When I issue "show start", the error message comes out as "%Error opening nvram:/startup-config (File table overflow)". It happened two t...
how i can remove flash partition on 3640.
The problem is as title, who can help me ,many thanks!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |