Cworks LMS 2.1 - We have visability of our routers by both the Serial and Ethernet ports. Which is the best interface to use for adding the ip and snmp strings to, for the functionality of ani, rme etc the Serial or ethernet??
Cworks LMS 2.1 - We have visability of our routers by both the Serial and Ethernet ports. Which is the best interface to use for adding the ip and snmp strings to, for the functionality of ani, rme etc the Serial or ethernet??
Hi All,In ntp, when use authentication, I saw a sample config:ntp authentication-key 1 md5 0256550A5B5629701B1B514951 7ntp authenticatentp trusted-key 1ntp clock-period 17179825ntp server 172.25.10.2 key 1The question is I don't know when should the ...
Can anyone tell me what the difference is between a Sup1A and just a plain Sup1 ? Sup1A says it has L3 Switching Engine WS-F6K-PFC SAD0451035X 1.1 and the Sup1 has L2 Switching Engine II WS-F6020A .IS there any performanc...
HelloIs it possible to perform a GSM (V.110) Callback with a BRI interface and Radius authentication? And perhaps someone has a example configuration!?Alex
This should be simple. I've done it before. I just want to hang a 2950-48 off a 2950-24 via a trunk. The -24 is trunked to a 2612 on a fastethernet NM and works fine. This is the layout2612(fa1/0)<>Sw1(fa0/1)-Sw1(fa0/24)<>Sw(fa0/48)They are all dot...
I have 3 switches. The core 4006 is the the spanning tree root. A second 4006 is trunked via gig to the core 4006. A 5513 is connected to the core 4006 via a gig link.I moved all the connections for one of my VLANs to the 2 4006's. My assumption was ...
Hello,I have a cat4003, with SupVis1(WS-X4012). With sh log, there is a message 'NOTE: Use "show crashdump 1" to see the crashdump.' At begin of this file is I can see:'Version and date:Old crashdump format or invalid Version and Date '(IOS 6.3.(7...
I have an Catalyst 4503 with :IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-IS-M), Version 12.1(12c)EW1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1).I want to know if it support RSPAN ? If not, is it possible with an upgrade ?Thanks
I am able to connect to a modem attached to a switch's console port, but am not able to communicate with the switch for remote management. I expect a specific cable pin-out is required and some config change ??
What does it mean the following message :%SYS-4-P2_WARN: 1/Tag 0 on packet from 00:d0:59:18:41:05 port 2/5, but port's native vlan is 17Thanks,Christophe
Dear All,I want to connect 2 ISDN Bri thru WIC-2A/S on cisco 2621 router.the things to be taken care.1. DDR2. need to support around 4 sites thru 2 ISDN bri.so it may happen that separte client dial to same ISDN and need to be connected at a single ...
I have an exising 827 configured for PPPoA using a dialer interface (dialer profile). If I create a Policy-Map and apply it to the Dialer interface for egress traffic the interface goes down. If I debug it complains about not having a dialer string...
I am installing LMS 2.1. The guide said RTM has to be in a dedicated machine. Can I still install the RTM together with other LMS modules in the same server ?The server is only used for network management. ( HP NNM and ciscoworks 2000 )
Hii want to ask about the benefits of having Multiple areas in OSPF network..?i see that the only benefit is optimizing routing updates..and making summerization on ABRs.., but if the networks are not distributed contigiosly across the network.., and...
Can someone tell me if I have this right?I have a core switch which has connections to all access switches in the LAN. Everything is on VLAN 1. All ports are non-trunk ports.I connect a new switch to the core switch. The new switch uplink port to ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
01-22-2025 07:00 AM | ||
12-30-2024 06:12 PM | ||
11-14-2024 09:33 AM | ||
10-24-2024 11:51 PM | ||
10-20-2024 10:52 PM |