Can I configure two VTP Server in a single VTP Domain ??Do I need to configure VLAN on both the VTP Server or only on one server.Pl. help
Can I configure two VTP Server in a single VTP Domain ??Do I need to configure VLAN on both the VTP Server or only on one server.Pl. help
Quick question here. If I bridge a network using two 1721 routers do I still need to point the PC's gateway at the router?I ask since the PC's current gateway is pointing towards a DSL modem that provides the internet access.
i'm new is cisco product, after the spanning traffic, is the traffic uni-directional or bidirectional traffic,e.g after spanning, can spanned port traffic go out to other port which traffic pass to other port ?
We have a router 2621 (MPC860) on which runs the ios 12.0(4). When connection Isdn BRI is activated, we have this message:"%pquicc-1-toosmall: pquicc[0/0], packet was less than 2 bytes" what does that mean? and if it is a problem, is there a soluti...
For both Catalyst 2924 and 3524 switches, SPAN can be configured using Switch(config-if)# port monitor vlan/interface command. However, I have noticed that this command works only for VLAN 1 and Cisco documentation I looked at also suggested the sa...
I'm having trouble with a rate limiting configuration. The pertinent commands from my config are below. This switch is in a metro Ethernet environment. I just need to be able to lock the ports down to a predifined rate regardless if traffic type.IOS ...
Does anyone know if the RSM has to be installed in slot 3 or higher (like the Cat 5000 series) or can it be installed in slot 2? I get an error trying to connect to "session 2" . If it has to be in slot 3 that would make sense....Thanks in advance!
i have two 6509 as distribution switchs and just 2 4000 at the access layer. When I ping between access switchs or to distribution switch. The round-trip time I got is usally great than 8 ms. all the swiths are in same building and one access sw is n...
I have a switch 2950 switch providing connectivity to remote site users through a connection to router. No trunking configured and being a stand-alone switch no VTP configured on switch therefore by default it configured as server with ver. 2. But, w...
I found that UserTracking can capture MAC info. from the switch port which individu VLAN has been assigned, but can not capture MAC from the switch port which was configured as trunk. Why? As I know the switch actrually maintain a MAC table with info...
Anyone know what this field means when you do a show counters (dmaMacMismatch) ? If this field is incrementing what does it mean ?
I am currently running 12.2.-12a IOS with IPX enabled. when i have a client dial in to the router running 95 or 98 they route IPX fine, if they have NT or W2K they can't get to a IPX server. IP seems to be working fine. We are using the nextport m...
I have 4 4912's and I noticed that the LED's for utilization never light up. Is this a hardware problem on these switches?
Hi,we have NASes AS5300 running IOS 12.1(14). We want to activate "modem call-record terse" command in these NASes and we would like to know if this could be dangerous or problematic.Is there any other command similar to this?. Is this the correct co...
Hi, I want CiscoWorks for a SUN solarisV8 to manage our LAN/WAN. I need to be able to do configurations, real-time monitoring, alarming and QOS policy implementations. together with HPOpenview.very confused which modules to buy.Can someone help me id...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |