HiDoes anybody know how to adjust the TCAM in cat6k (msfc). at the moment it is showing 91%usage ThanksAtul
HiDoes anybody know how to adjust the TCAM in cat6k (msfc). at the moment it is showing 91%usage ThanksAtul
My 6509 LANE module got this message, and Idea ?ATM Driver returned HOST_IN_BREAKPOINT to send,port 0 vcd 1 length 8 data @0x019717F8THANKS
Hello All. Is anyone aware of the ISDN switch type used in the United Arab Emirates? The ISP there is called "Etisalat". Regards, Tariq.
Applications like billing and accounting needs reliable connection which is not present in netflow.How do you flocks account for reliability with netflow?Thanks in advance,Senthil
Hi.Could you tell me is it possible to make a trunk for auxliliary VLAN?and if it is possible then will it be participant in the spannig tree? What is the disadvantage of it?
Two cisco router 803 were connected through the ISDN , I set these two router as a bridge.I could ping the remote site internal host. However , it was fail to ping the remote bridge serial interface.There was no remote site s0 MAC address in the arp...
I have a cisco 7200 and 2600 with IOS 12.2(5) installed and have observed a problem when MLPPP and Interleaving is configured.firstly, the ppp multilink fragment-delay command, has only one setting.Any setting above 50ms fragments the ppp packets int...
Is is possible/advisable to have to routers that have one interface in area 0 and one in the same other area (say 1 for giggles.)? I'm looking at having two routers, each with an uplink to our primary lan. Within this secondary lan there are mulitp...
Is there a way to reset a 7206 router to factory defaults so that the startup-config. and run-config. has been set back like it was when the router was taken out of the box beside typing the no command for each line of the running-configuration and t...
One of our routers, is issuing some messages shown below:"%Error opening tftp://255.255.255.255/network-confg (timed out)""%Error opening tftp://255.255.255.255/cisconet.cfg (timed out)"No other error message appear.We did not find out any explanatio...
I've experienced these problems everytime I enable dual b channel of the ISDN to connect to the Internet. The commands that I used are interface bri0 dialer load-threshold 1 either -> because I want both channel to be up all the time ppp multilink Wi...
Hi,I have an E3 link b/w 2 sites. The E3 link is set up at both ends using a PA-E3 with a Cisco 7206VXR router. The PA-E3 module has an integrated DSU. According to the ISP, the E3 line is not terminated remotely with a DSU. In that case, should i us...
Hi all,i have a 3640 Router for Dialin Win-Users with callback enabled. With IOS 12.2(6) all works fine, but another 3640 with IOS 12.2(2)T can't callback.The errormessage is: ISDN BR2/0: Error: Unfound B-channel on Progress after callback timer exp...
Hi,You know, 35xx series will be obsolete soon which will be replaced by 2950 series. 2950 does not support ISL trunking. However, my existing network is using ISL. Can ISL and 802.1q co-exist in the same network ? (i think so)If yes, any extra thing...
At the moment I'm using a route-map in the eigrp process to limit the routes provided to eigrp but the access list I require is quite long. Is there any other,neater way to only pass a default route to the eigrp users?ThanksBenjamin
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |