We have purchased new 2950 switches but we are unable to connect the pcs with novell netware v3.12 server. we are using 3com's ISA network adapter in server and 3com's 3c905b network adapter in workstations. What should i do to solve this problem
We have purchased new 2950 switches but we are unable to connect the pcs with novell netware v3.12 server. we are using 3com's ISA network adapter in server and 3com's 3c905b network adapter in workstations. What should i do to solve this problem
We have an old copy of CW2000 Campus (RME+CSWI) for HP-UX 10.20.We finally have a machine with enough disk and ram to actually run it to see if we want to keep it (it's been sitting on a shelf for a couple of years...)The essentials OSG won't stay ru...
How can something "Break" the switching fabric? I have a Linux server that is uplinked to a Intel 510T switch that is uplinked to another Intel 510T switch which then goes gigE to a cisco 3500XL and then gigE to a cisco 6506. If I dump the packets o...
Does anyone know if a Catalyst 3534 supports the standard 802.3ad Link Aggregation protocol or just PAgP on a gigabit interface?
We have a 1601 Router that was shelved a year back. And now we are ready to put it back in service but do not have the password for the router. We also do not have the console cable. I am making a new one right now. Is there any way to reset the r...
We have a Cisco 1601 router connected to the internet via an ISDN connection. The problem is that our ISDN connection keeps dropping very often if there is no traffic on the line. The router is configured with an idle-timeout value of 999999. When w...
Hi,I've been using the SWIM function of RME to upgrade some 4006s to code level cat4000-k9.6-3-5.bin. Having performed a few upgrades, I've now come across the following error message each time I choose a 4006 device for upgrade.Internal Error: Inva...
A question that has been asked many times before ;-If I had two remote sites A & B. There are two WAN serial conenctions (10Mbps)between each site. Each terminating on its own router. Site A Site B ----- ...
I want to connect a new switch in a network ? revision nummer prob etc?thanks
We are giving access to our customers through 2 CISCO 3640, each CISCO has 2 PRI ISDN interfaces . Behind these routers we have a FW over a Sun workstation. Our telco has configured the PRI numbers with 'load balancing' this means that every call ...
Hello!I have a problem with Configuration Management from RME 3.3 on WinNT.When I try to Update Archive and select a device from list the operation fails!More info...Probable Cause: failed to initiate telnet session, cannot resolve host PIPPO!!!But I...
Hi every bodyMy Cisco 1720 router dial to internet and everything is OK if it have connected an analog modem (USR 56K message)but if I change this modem with an Zyxel Omni.net LCD (ISDN modem) on the same serial port it doesn't dial. Any ideea?best r...
How I can obtain the information of received calls and cost of them in ISDN.Is this possible with CISCOWORKS?
Hi, I have a 8 port switch and 4 computers.One is going to be my internet server by running Linux and the other 3 computers are going to use Windows Me, Windows XP and Windows 2000 Professional.Since I have to get a dynamic IP address from my ISP, ca...
We are planning to implement Catalyst 6509 now. Does anyone know any good reference books, links?Thanks in advance
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |