Other Network Architecture Subjects

HI I have a 3640 router, it has 8 MB on board Flash n 8 MB PCMCIA. I have an image that is 10MB, is it possible to logically combine these two so that i can upload 10 MB image. I understand that this is not a platform related question but I dont see ...

I have configured a 3640 ( IOS version 12.1 (4) )router for dial up access with three lines. I have noticed that many users stay connected for hours together. I want to impose a limit of say, 30 minutes for user sessions. Is this possible through any...

I know that serial interfaces might differ in their maximum throughput, but I have not any numbers. Can anybody give me the numbers for- asynchronous/synchronous interfaces (NM and WIC)- synchronous interfaces (NM and WIC)- smart serial interfacesTha...

Hello,My question is about the nature of inverse arp: I've seen that if I configure a meshed Frame relay Networks with subinterfaces (point-to-point but also multipoint), if the inverse ARP is not activated, to permit the routing update of a routing ...

I have been trying to find any reference that states if there is a limitation or a design recommendation on how many bgp peers a single router should have. I know that for OSPF the recommendation is 50-60 neighbors, and for EIGRP it is around 40. I...

I have a CISCO 806 that I will be using to connect to a RCN 1-way cablemodem setup. This will replace the existing Sonicwall.I can get the router to get an IP address from the network, and it is serving DHCP to its connected devices. But I can't re...

Am I correct in saying that the command:SET SPANTREE PRIORITY 0 5will prevent this particular Cat5000 from ever becoming the root for spanning tree on vlan 5. I think so but I'm not positive. Can anyone confirm this. Thanks.

We have dynmamically allocated IPs from our ISP, without a static address is there a way to get the 1605 to get the dynamic address from the ISP? OR should I get the static IP?

I am from Indonesia I have problem in my network after I install Switch Catalys 2900 and Catalyst 2900xp. My server and workstation are macintosh. Question :Why this happen ?, some of my computer 100BT Dupplex:Full some of them 10BT Dupplex : half,.I...

I am planning on a multi-casting star topology network with one head end router and many tail end routers. What is the most convinient way for me to manage and change the configuration of one or more tail end routers if I have not install Cisco Work...

Hi,all.Recently I was working on a project,my custom asked me to setup 70 VLANs on Catalyst2948G-L3. But the problem is there are only 16 bridge-groups on Catalyst2948G-L3,so I have to put all VLAN in one bridge-group.But it is not safe put so many V...

I am trying to configure ppp multilink over to existing serial lines. I have used the following config on both endsip subnet-zero!!!!!!interface Multilink1 ip address 10.201.10.2 255.255.255.0 no cdp enable ppp multilink multilink min-links 2 no ppp ...

I have a 3640 running 12.0(1). In that I have a network module that can take 2 WIC cards. Whenever I try to add the second WIC the other interfaces go down..(Serial and FastE) I have ruled out hardware and lack of memory. Has anyone else experienc...

Hi We have Cisco 6509 layer 3 switch and do lan route, ver 12.0(3) with vlans. I cannot do deny ip traffic on the vlan interface, like access-list 108 deny ip any anythen on the vlan 4 interface ip access-group 108 inthen, from client mach...

In page of reference Cisco I found information for install flash card MEMC6K-FLC24M in C6506. In this document say that is necessary update ROMMON for compatibility, but I don't know if is alike for flash card KCS-FC6000/24 (Kington Memory). Is c...