I have added the following to my VLAN in order to see ALL traffic passing both ways:access-list 110 deny ip 10.0.0.0 0.255.255.255 anyaccess-list 110 deny ip 172.16.0.0 0.15.255.255 anyaccess-list 110 deny ip 192.168.0.0 0.0.255.255 anyaccess-l...
I have added the following to my VLAN in order to see ALL traffic passing both ways:access-list 110 deny ip 10.0.0.0 0.255.255.255 anyaccess-list 110 deny ip 172.16.0.0 0.15.255.255 anyaccess-list 110 deny ip 192.168.0.0 0.0.255.255 anyaccess-l...
simple question: I can't remember how to resolve the following issue on my console connection via a term server - i connect in and then observe the following 'echo' when entering a command:sshh rruunneach character gets 'echoed' i seem to remember ...
I have a Catalyst 6509 with supervisor 720-3B and IOS 12.2(17d)SXB10. I have installed a X6704 4 port 10Gb card in slot 1 and powered up the system. The X6704 is recognised but is powered off with a message stating that it is not supported. Using sho...
Can a range of IPs be excuded from NAT?
Hello,I am looking for some clarification of CEF switching behavior when using the following topology. 2 layer 3 switches, A and B, directly connected via a dot1q trunk and 2 hosts, C and D, both connected to switch B. Host C is in VLAN 10, Host D is...
We can't get any translations to show on our router when connecting from the outside. I was looking at the config and was wondering if the sub-interface portion was correct. I am curius to know that if I put an IP on fa0/1 (instead of fa0/1.1) if thi...
What is the easyst way to configure an catalyst 3750 switch to limit traffic going to an ethernet port.I want to adjust the throughput of an 100 mb ethernet port so that only 5 mb is going through.I was looking at traffic policing and shaping. But i ...
Hi All;I have 2801 which I downloaded second IOS image. How can I load the router with second IOS image but keep the old IOS in the flash?ThanksAlex
Hello,I urgently need to know the differences between the 2950 EI and the SI.I need this info urgently in order to make a purchasing decision.
Hi Everyone,Would anyone know what the maximum number of T1 the can be installed into a 2851.Also, would anyone know what the break-even point would be when to install a T3PS: This is for a voice project. Lines will be used for Voice only.Thanks.-- D...
What is the algorithm used to distribute traffic between the ports of an etherchannel on the 3550? We are using the default distribution method of source-mac. Is there an IOS command I can use to see which port the traffic is using?
This is a truly odd situation, I have a 2950 running IOS version 12.1(22)EA4 and I have set up probably hundreds of Layer 2 switches, and I set interface vlan to a static ip within 24 hours it changes itself to a dhcp ip address. I thought someone w...
I have a network consisting entirely of 2950 switches although some are 2950Gs and the rest are just 2950s.I am running CCTV video encoders over the network which generates a lot of multicast traffic. The multicast traffic appears to be forwarding o...
HI all,Here is the relevant output in the config, I´m trying to create an etherchannel between a 3750 switch (working in stack mode) and 7304 router.ROUTER 7304!interface Port-channel10 no ip address no negotiation auto no clns route-cache hold-queue...
I am trying to set up an 871 router (1 FE WAN port, 4 FE LAN ports as an integrated switch) for a small business with classic internal, perimeter back rail, and perimeter front rail networks. Each of these networks is currently set up on a segregate...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |