I would like to bring to your attention an observation regarding the link speeds of different access point models connected to our Cisco C9300 PoE+ switch. We currently have three types of APs in operation: C9200 AP – Showing 2500 Mbps on WLC C2800...
Forum Posts
Is the column of wireless client monitor below can be customized? I need to showing the client devices name where now i only can see the name if we click on each client. Tyr to exporting the data but the device name is not showing.
Good day. C9800-CL. There are two Wi-Fi networks, guest and work. There is a TV that is used as a wireless display. Connected to the guest network. Users of the work network see it as a wireless display, but cannot connect to it. I read that this can...
Hi Team, We have deployed 9800-40 WLC's which are in HA SSO and for RP port connectivity we have used fiber RP port direct connection now we want to connect secondary RP port which is RJ-45 which will be through L2 swithh. Please confirm whether it i...
Resolved! Remove Insufficient License
I have wrong assigment license for my AP, previously i assign DNA Advantages in the controller and i change to DNA Essential because this is license was purchased. When the AP using DNA Advantages then in the smart account i have insufficient license...
Dear team, i have c9800 wlc and i have create 2 ssid one for gust user and other for corporate user.i want Gust user access only 10 mbps download and upload speedi want corporate user access only 20 mbps download and upload speednote: i have isp li...
Hi all!I have a question about WPA encryption. Does Cisco support AES (CCMP or GCMP) 256-bit on WPA2 Enterprise or WPA3 Enterprise (not 192-bit mode) on both AireOS WLC and C9800 WLC?Thanks.
Why ap is blinking red/green 9120ax
Hi AllI'm running for testing a 9800-CL in VMware Workstation with 17.15.3 (initially installed with 17.9.6). There are no APs attached to it and just the absolute minimum configuration (web gui setup wizard, NTP and a valid user).When I now try to i...
HiWe are using a CW9166 Access Point managed by a C9800-CL Wireless LAN Controller (vWLC) running image C9800-CL-universalk9.17.15.*Through the vWLC GUI, underConfiguration > Radio Configuration > High Throughput,we reduced the number of spatial stre...
Resolved! AP 9130 AXI-e in EWC
Hi I have an ap 9130 I want to run an wlc in EWC mode. I followed this guide However when I cmd ap-type ewc-ap tftp://192.168.0.82/ap1g6a tftp://192.168.0.82/C9800-AP-iosxe-wlc.bin Image upgrade not needed, changing AP Type to EWC-APa show version AP...
Resolved! C9800 Web Auth
Hello, I try create SSID with Web auth for my guest. When i select 'none' in Layer2 security and tick Web Policy in Layer3 why the SSID is not showing? If i untick the Web Policy in Layer3 then the SSID is showing with open authentication.
I have few WLC having configured as : %IP_SNMP-4-NOTRAPIP: SNMP trap source GigabitEthernet0 has no ip address errors on WLC logging and it was working fine before, actually there are similar WLC with same config are also working fine. I have configu...
Resolved! Band Select
In wireless environment should we enable the 'Band Select' or not? Based on this document enabling the Band Select will make 5Ghz will more attractive so the client will try to join to the 5Ghz first. https://www.cisco.com/c/en/us/td/docs/wireless/co...
Resolved! C9800 Test radius server
Good day. Tell me why the radius server test command is not accepted? It says: Invalid input detected at.
