I have Cisco IOS Software, C2960X Software (C2960X-UNIVERSALK9-M), Version 15.2(2)E3, RELEASE SOFTWARE (fc3) and I created an access-list to prevent my network to access other 4-networks, the 4-networks I can not access the SWs. when I tried to conf...
Hello cisco community. me and my classmates are doing an assigment made by our teacher. we have to make a small network by 3 pc's 1 router 1 switch and 1 wireless accesspoint. some of the requirements is to setup source NAT, DNS forwarding, SSH and a...
i have configured BDI interface on ASR Router (ex BDI 100) And given it Test IP 10.1.1.1/24 and it is UP and server with IP 10.1.1.2/24 can Ping BDI interfacebut when we shutdown one of Sw interface ( Ex: SW-01 Port Fa0/1 ) , Ping fails .It seems tha...
Hi, If suddenly license expired, will router unable to be configured with BFD? Originally, router is configured using BFD. Then, noticed that router down and unreachable remotely. But later when I checked the syslog, there was no log that indicate ...
Hello I have already posted this in the security forum and as of yet had no feedback so now i am trying R/S forum just in case someone could answer this. Our own FW admins dont know and I cannot find any documentation on CCO, The answer I am lookin...
Wondering if anyone could point me in the right direction on the best way to configure NAT Overload / Fail over between two ISPs. One has a Dialer 1 interface (Gigabit 0/1 Interface) the Other is a Gigabit 0/2 interface Many thanks.
Hi,One of our branch offices is connected via an SDSL connection to a Cisco 878, which in turn NAT's a FortiGate 110-C behind it. Obviously, this creates a double-NAT network and is suboptimal.What I'm trying to achieve is the ability to assign the s...
Hi all, We're trying to set up a eBGP connection between a Cisco C3850 (our side) and a Nexus 7000 (customer side). First i got "mal-formatted" messages from the Nexus 7000. The Nexus side configured "dont-capability-negotiate" and now i'm getting ...
Dear Friends I have two routers cisco 2911 and other cisco 810 series 1.) Cisco 810 is connected with MPLS for remote sites to access the Host system 192.168.2.0/24 Cisco 810 is working as gateway for both MPLS and local site 192.168.2.1(I dont have...
Hi all, Consider two extended ACLs (extended_ACL1, extended_ACL2). If I want to apply both of them (allowed by any one of them) on the input for an interface I have to create a new ACL(merged_Extended) and then apply using "ip access-group merged_...
Hi, I need to use two Nexus 9300 to replace a three unit stacked catalyst 3750 switch for a small datacenter. The catalyst switch is the default gateway for local LAN and has eigrp running to peer with two other locations via private WAN. I have N9K...
Hey guys, this is my first question in this community! I need to create an ACL that blocks access to Sydney DC, and DNS servers but allow access to MySQL, Exchange and Apache. The traffic is coming IN from PC13 (in the top left of the image). I've be...
Hi What is the throughput of the Cisco 2901 router. Can i have 1Gbps internet connection to this. Will this router support this speed as a Internet CE router ? rick
i am setting up a Cisco isr 4431 when looking thru my config my username / password is in clear text . is it possible to mask this password? #username username password 0 mypassword
I have a Cisco 1841, coming from the 10.100.100.0 network, i would like to be natted for the 10.20.1.0 network as i was coming from the 10.20.1.1 interface and for the 10.50.1.0 network as i was coming from the 10.50.1.1 thank you
