Hello, We have two ASA 5505 8 port, basic licence devices that are used to allow a third party VPN to interface with systems on our network. Currently 3 of the 8 ports are connected an in use. One port is the local interface, another port is an o...
Forum Posts
is there a way to do multiple destinations on netflow data on interfaces? I'm trying to do this because we need to extract outside and inside. i am not finding any reference to it and it looks like i can't do it.
Hi, I've been having major issues getting WCCP and the Zone Based Firewall working together on an ISR4331. To rule out the Zone Based Firewall, I've removed all of its configuration. I still can't get WCCP to work! Clients are on 10.10.0.0/16, t...
Hey all, My current ISR's are having multiple technology packages , now im upgrading to a new set of ISR's with a new IOS version. How do i transfer these package licenses to my new ISR? Any thoughts ? Thanks
Hi AllIs it possible in IOS to have for a particular subnet:a) Two static routes?b) Make one static route a higher priority than the other?c) If one static router "goes down", failover to the lower priority static route?We have a l2tp/vpdn connection...
Never mind my fault was very silly issue and I need to delete this topic but I don't see any delete button!
Hi, I am currently using C3750X-24T-S model with the firmware version of 12.2(55)SE5. I had activated my license with "ipservices"as because WCCP configuration will require either IP Services or Advance IP Services feature set as stated in the datash...
Hi there, We are looking at implementing load balancing between 2 different MPLS carriers for all of our centers globally. In the U.S. there's no problem as we are all connected to the same AS for MPLS1 and MPLS2. However, in APAC, EMEA, LATAMS reg...
Hi, I have a problem with two switches, first I describe the scenario: The switches are connected via two fibres (dedicated lines) conected to the switch with media converters, the client dosn't know if the fibre is a dark fibre or a switched fibre...
Hello I am implementing pbr to force a specific SRC ip subnet in vrf_2 to use a next-hop in vrf_1. 4500x-1-#sh ip arp vrf vrf_1Protocol Address Age (min) Hardware Addr Type InterfaceInternet 10.229.254.253 89 a80c.0dc0.fc3c ARPA Vlan229Internet 1...
Hello, I am new to packet tracer and I am trying to ping PC A to PC B with no success. They can ping correctly within the same network like PC B to Switch B but cannot get across the routers (etc. ping PC B to Router A fails vice versa). I set the ...
Hello all! Thanks for looking. I'm currently looking into a new install / upgrade of a couple of 1921 ISRs with EHWIC-4G-LTE card that has a ezvpn. New routing solution will connect to new firewall appliances, and as I understand it FTD firewalls w...
Resolved! %BGP: This may cause traffic loop if not used properly (command accepted) , isn't a problem?
Good morning to all, Actually in my job we are modifiying the configurations from IOS 15.4(3)M3 running in two CE routers 2951. We are adapting to IOS XE 15.5(3)S6 running in two CEs routers ISR 4321. There are a backdoor link between them. We use...
I am unable to ping R2 from R4,i had removed routing from R4 and considered it as an end device.Please help me why i can't ping R2 from R4,what is the problem,80.0.0.1 is taken as loopback on R2.Im getting the error as (UNRECOGNISED HOST OR ADDRESS,...
hello we have an ISR4451-X/K9 running isr4400-universalk9.03.13.02.S.154-3.S2-ext.SPA.bin we have an ISR4451-X-4x1GE module installed g0/0/0 presenting rj45 to the LAN g0/0/1 presenting an SX SFP to the WAN when the customer moves g0/0/0 into a new ...
