Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

ISR 4k

I'm new to the forum, I have quick question. What's the best practice placing ISR 4k router before or after dedicated firewall. For multi wan deployments. It's seems like that all design guides for UCM pointing on ISR being in front. Thanks,

Simke-360 by • Level 1
  • 278 Views
  • 0 replies
  • 0 Helpful votes

867VAE EzVPN client connected but no local access

Hi All, First off apologies but I am new to CLI and an trying to setup an ipsec vpn from iPhone/ipad to router.  I've setup Easy VPN Server and remote on an 867VAE using CCP and I am able to connect to server and ping vlan1 interface but cant ping ...

cymak by • Level 1
  • 396 Views
  • 3 replies
  • 0 Helpful votes

Resolved! BGP Route Map with Regular Expression Issue

I have a router connected to two MPLS providers and I'm learning how to use local preference so traffic is preferred by Comcast MPLS over the second MPLS (AS 4321). I have the configuration below on the router but it won't match until I remove the re...

Resolved! routing multiple gateways site-2-site VPN

I've got an odd setup and need some help. We have and ISP with a /29 network. We connected the Ethernet handoff to a layer 2 device and connected one end to an Calyptix firewall and one to our Cisco 2811. the router currently has a default route that...

Pfr auto tunnel

Can someone explain where the auto tunnel's bandwidth is derived from, and what significance its utilization might have?  The output of sh int tu0 seems to indicate that lo0 is the source, but their values are very different.  I noticed on one of our...

ibgp local pref not preferred over ebgp

Hi Guys, I am slightly confused by the lab I have setup in GNS. My ibgp neighbour seem to have local preference of 100 by default so I would expect that to be picked rather than my ebgp which has local pref of 0 why is ebgp still picked? isn't lo...

cisco8887 by • Level 2
  • 1055 Views
  • 6 replies
  • 0 Helpful votes

Resolved! Serial over IP

Hi. Having 2 windows computers with hyperterminal (in real life i have 2 non ip devices with rs232, 19200 bps, flow control: none, stop bits 1. For the purpose of test i'll use hyperterm) and 2 cisco routers 2811. Each workstation terminates a serial...

c.captari by • Level 1
  • 2320 Views
  • 7 replies
  • 0 Helpful votes

0 bits/sec output rate

Hi  I am seeing 0 bits/sec output rate whereas the around 26Mbps traffic ingress to the interface.  What does it indicate? How the return traffic is not showing as output packets? 5 minute input rate 26319000 bits/sec, 3017 packets/sec 5 minute outp...

Resolved! ASR1001-X - 10Gig interface

Hello Friends, Does anybody know if it is possible to bring up a 10Gig interface on an ASR1001-X without the licenses L-FLA1-1X-2.5-10G, and L-FLA1-BIN-1X10GE? One of my customers wants to try it. Regards,

Router rip + GNS3

So there is this simple GNS3 topology. The host is Ubuntu Linux tap0 interface. ifconfig output: tap0 Link encap:Ethernet HWaddr fe:6b:25:17:ab:af inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::fc6b:25ff:fe1...

Load more