Resolved! How can the ISP's default gateway be in a different subnet and still work with my public address?
How is it possible that the default gateway on 24.205.84.1 works with an address 24.205.86.91 /30 on the wan of my home router?
Forum Posts
Resolved! Packet Tracer routing doesn't work
Hello all, unfortunately I'm stuck and I don't know what to do. I configured the switches: created VLAN 10,20trunk with vlan trunk allowed vlan 1,10,20 between the firstfloor and secondfloor switchestrunk from secondfloor switch to routeradded client...
Hi all,I've been given a PT file (attached) to troubleshoot for a uni module. I'm slowly getting to grips with routing, but this one has confused me.I've worked my way through the IPv4 and IPv6 configurations and made a list of what I think is wrong....
Resolved! Rputing RIP v1
HI everybody. I doing so small study project with routing RIP v1 for study.All network work in same net 200.100.100.0 but i got couple router between department. Mayby somebody get some advice for me. i attache project from packet tracer
Resolved! routing
hello, do you guys know why does my pc12 can't ping to server and, please check my network configuration i am not really confidence from what i've configured it seems like i miss something important, thank you
Good afternoon all.I have about 50 sites, all of them have extended ACLs, with the networks source IP (different at each site) and some destination hosts( that are the same at each site) , that can change every few years as we upgrade our systems.The...
Hi all,we just installed ncs57C3 mod in our datacenter as core bgp router and it reboots itself alnost each 3 hours. Here is the log: 0/RP0/ADMIN0:Jul 5 07:33:48.000 UTC: shelf_mgr[2131]: %INFRA-SHELF_MGR-6-HW_EVENT : Rcvd HW event HW_EVENT_OK, even...
I just purchased a cisco 1921 off e-bay and it appears the current config has an att config that I can not reset. I have tried booting into ROMmon to no success. I have tried taking out the flash memory and booting a few times to try to get it to boo...
Could anyone please assiste me here?I have a Cisco 9001-LC that is stuck at rommon.I'm trying to turboboot using asr9k-mini-px.vm-6.4.In Rommon, I am not seeing any Disk available and I am unable to see the usb when it's inserted.devDevices in device...
Resolved! BGP "update-source" command odd behavior
Hello everyone,I was setting up a simple lab and came across what, in my opinion, is an anomalous behavior. Below is the photo of the topology. So, I have 2 routers, R1 and R3, with their configuration provided below. I tried to create a BGP session...
Resolved! Issue Pinging to 8.8.8.8
Hi Team,I have an issue with this topology, the main switch can ping to the main router on the vlan subinterfaces (192.168.10.2 and 192.168.20.2) the internal PCs can ping these subinterfaces as well. Now the issue is, the main router can ping to 8.8...
Hi all!Here is the topology: I use FVRF to configure the DMVPN, the overlay and underlay of the Hub are both in the global routing table, and the underlay of the Spokes is in vrf UNDER, the overlay of the spokes is in the global routing table. I use ...
HELLO , I've configured an L2VPN point-to-point xconnect between the interfaces G1/0/13 and G1/0/11 using the following configuration l2vpn xconnect context testmember GigabitEthernet1/0/11member GigabitEthernet1/0/13 interface GigabitEthernet1/0/11...
Resolved! Can't ping to MGMT VLAN Interfaces
Hi Team, I have a problem that I can't do ssh to these switches (mark red), but I can do ssh to these multilayer switches (mark green). Anyone have the same issue with me? The background is that all of these devices must be remote controlled from a ...
Hi All , We have configured IP rtp compression on E1 link but the packets are not getting compressed. If anyone has any clue , kindly advise. Although IP header compression is ON although RTP packets are coming on interface still we are not receivin...
