Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

HI i am currently banging my head against a desk trying to figure out what i am missing here, I am trying to configure A Cisco 887VA router to connect to the internet:I can get the router to ping www.google.comI can ping the internal LAN (192.168.0.2...

Hi,I have seen outdiscard errors on almost all the interfaces on a 3750 switch,  The other counters are fine.  Please see example belowPort        Align-Err     FCS-Err    Xmit-Err     Rcv-Err  UnderSize  OutDiscardsFa1/0/1             0           0 ...

pokwan by Level 1
  • 1656 Views
  • 6 replies
  • 0 Helpful votes

Hi can you please help me with a problem with my cisco 1760 router. The problem is that the router outputs in the console         "▒`g▒_7[▒▒▒▒f▒e▒▒s#▒▒▒'▒ܱ▒▒Z▒▒                            ۔3▒r0ndYα▒6▒▒▒ڸ^▒▒lc▒▒ܫ▒'▒▒&▒tK                               ...

Hi guys,I've implemented dual internet on my cisco 2811 router, everything is working properly and after a period of time the router gives the below message thousand of times and reboots%SYS-2-INTSCHED: 'suspend' at level 3 -Process= "IP NAT AgerPlea...

I need a router 1921/K9 and checked its datasheet,http://www.cisco.com/en/US/prod/collateral/voicesw/ps6789/ps7290/ps10589/data_sheet_c78-598389.htmlnoticed words:The Cisco 1900 Series enables deployment in high-speed WAN environments with concurrent...

Hello, we have primary MPLS link and backup ISDN on our Cisco 1921 routers, i have noticed that logs show ISDN link keeps going up, and then down after a couple of seconds. I dont see any reason for this happening since our primary link seems to be w...

Hi Guys,kindly check the attached diagram for my questioni'm having 3 live servers in my LAN which are access-able from outside my network. I'm doing NAT for these 3 servers on sonicwall firewall.earlier we were using ADSL line but now we have got 2 ...

Hello EverbodyI have 2 router ( setting as HSRP Standby )My lan point to the defaut gateway of the standby address ( 10.30.21.6)On the Router 1 (high priority standby ) i have configured on the lan interface a PBR that redirect traffic http/https  fr...

Hello everyone!One of our end clients Cisco 1812 running IOS version 12.4(20)T. is experiencing high memory utilization. We dont have any reports of any network performance issues other than the fact that the routers memory utilization is aroung 85%....

Hi,I am very new to CISCO. Our office bought a CISCO 2911 Router. Fact is: from ISP to connect with WAN we got real Ip of : xxx.xxx.xxx.10 / 29 and their gateway is xxx.xxx.xxx.9 . In the office I need to setup LAN with IP block 192.168.1.1 Subnet Ma...

Pretty sure the answer is "yes", but is there a special license required to configure IP SLA monitors in IOS 15.1?  I'm trying to do this on a 2921 running 15.1(4)M7, ipbase feature set.Router(config)#ip sla ?    key-chain  Use MD5 Authentication for...

Hey All,I'm labbing up some BGP-MPLS and OSPF routing solutions. I'm doing mutual redistribution of BGP and OSPF at my WAN edge with route tagging for loop prevention. I'm setting local pref to 50 and weight to 0 when distriibuting OSPF to BGP. That ...

hypnotoad by Level 3
  • 1005 Views
  • 6 replies
  • 0 Helpful votes
Unanswered Topics