Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
I am having a problem configuring a VPN connection from a 1721 router to an ASA5520.The router has already been configured, but I have been asked to setup the VPN.I think the issue is because they are using a Loopback interface (which I have never co...
Hi All,How can i check the BW of a link that is newly comissioned from service provider.Suppose i have upgraded bandwidth to 5 MB from a service provider and i want to check it using extended ping command from my router to PE end router.What is the e...
I know how to give the dynamic ip by router to its networks.But i like to give the dynamic ip to vlan by L3 switch.Is it possible?:?? I want a help?
Hi !i have a nat statement : ip nat inside source list VLAN108_NAT interface GigabitEthernet0/1 overloadand i want to change it from interface dependent to a "floating nat" .can i use this ? ip nat pool VLAN_108_NAT_POOL 212.11.55.55 212.11.55.55 pre...
Hi,This is my first attempt at configuring an 1801 and I am getting extreamly low bandwidth.Tests show up/down speeds on aroung 100kbps. I can't see any reason with the possible exception of the show dsl capacity values which never seem to change.I ...
HelloISP provided Internet link over a Wimax Device. The switchport on which the wimax is terminated keeps changing from Orange to Green.Initially we kept speed and duplex auto but no luck then we changed as per wimax team informed to speed 10 duplex...
I am currently using a PAT overload statement to get public addresses on internet traffic.interface GigabitEthernet0/0.1encapsulation dot1Q 1 nativeip address 10.140.0.1 255.255.254.0ip flow ingressip flow egressip nat insideip virtual-reassemblyinte...
Hi,I have got my ccna voice lab configured and is up and running, my switch is configured with 2 differents Vlans (Data & Voice) and the fa 0/1 is configured as trunk port connecting to the CME router. I can telnet or ssh to all the devices on the n...
I need to create a backup connection between the main server and a router in the office. We have BRI s/t card into the office router.On the server side we have a PRI(30 channel) on the router. How do we connect both the sides using DIAL ON DEMAND rou...
Hi,Our current setup is like all the internet traffic is filtered by checkpoint. Also we are allowing all the port 80/443 traffic in checkpoint.Then we have 7206 internet routers.We are now try to install Threat Pulse(Bluecoat) which is on the cloud ...
Can somone please help, the router is always giving the below error:Error : compressed image checksum is incorrect 0xDC5C5348 Expected a checksum of 0x066C5349I have uploaded a new firmware but same issue after booting, I have check the MD5 ch...
Hi all,I am facing with an issue relate to vrf, I have removed the ip vrf vrf-nameThen tried to removed the IP nat outside/inside static x.x.x.x.x x.x.x.x vrf vrf-name and came up with no vrf name vrf-nameI then created all the vrfs with the correct ...
Hi All,I have a new ISR 1900 router on which i accidently deleted the default username and password and now i am unable to get in to router console.Also i am unable to break in to Rommon mode as well. Can any one help
Hello AllWondering if I can have some help with QOS classes and their behaviours.I have a network with 2 main classes, AF1 which I know is Bulk Data and Default class. The AF1 class has 9mb of the 10mb circuit applied and default c...
Hi Folks, For some requirements I need to block some routes into our network. To give you a example say I want to block 1.1.0.0 /16 in my network, I have done so by adding a static Null route on our ISP facing router. Now the drawback for this soluti...
.png "Hall of Fame"){kind=icon}
