I'm working with Cisco 819's and 829's that need a large configuration file for the AP803 side of the box. The engineers that developed the current setup procedure tells us to open a session (service-module wlan-ap 0 session) then copy and paste the ...
Hello, kindly i need your support as we connected GTM to discover global DNS from different two ISPs on two router each router have two VRFs, on first Router first VRF the main and second is the backup, on the second router the second VRF is the main...
Good day everyone, I wonder if the c8300-1N1S-6T(or any router within c8300 series) supports VRRP in none SD_WAN mode. I cannot find any information about vrrp support basically, even feature navigator shows that is supported in SD-WAN only. Does ...
I Stuck at this level , users are facing slowness issue,However if I check the throughput and bandwidth both are under control.I cant really find the issue here.Checks:Vpn parameters are identicals2s timeout value increaseBandwidth under controlRemot...
Hello all,I have read about networks being described as "only Layer 3," and as such require no STP protocol, examples being VXLAN-based networks like Cisco SDA or ACI.However, even these networks have VLAN's (like L2 VNID's in SDA), and they also sti...
Dear Concern, I face some issue for replace my switch. Here i share some log. LOG:2020 Dec 31 03:49:55 cisco-9000 %L2FM-2-L2FM_MAC_FLAP_DISABLE_LEARN: Disabling learning in vlan 1949 for 120s due to too many mac moves sh mac address-table notificat...
Hello. My network is fully EIGRP at the Data Center, but there is going to be another brand integrated at the DC, so need to use OSPF on different blocks.I would like to understand what could be the problems I could face if I use the next topology:[O...
Hi , our router suddenly crashed, does anyone know about a bug in the version? Version 17.09.04a Thanks
hi all, I'm wondering if its possible to route leak between 2 OSPF Instances running on different VRFs without using the GRT. I've not found much around asides from route leaking using a VRF and the global routing. A workaround would be from an OSPF...
Hello,We recently had a failover test between between our ISP 1 and ISP 2. The failover portion worked fine via the IP sla's but we were unable to pass traffic through ISP 2. I believe the issue is due to the switch we have the ISP connections coming...
Hello everyone!I want to configure NAT-Hairpinning on the ASR-1002X router (17.09.05a, for this I went to the lab and tested the configuration on the CSR (17.03.08a). NAT-Hairpinning i need to allow internal clients allow access our external services...
Hi all,I'm wondering why cisco Priority must be in increments of 4096?..Not increments 0,1,2,3,4,.... Is there a special reason about it? Thank you. cf) Port 30 (TenGigabitEthernet0/2) of VLAN0002 is designated forwarding Port path cost 2, Port pr...
Hello community,We use C8500 for PPPoE subscribers. Configuration via bba-group and virtual-template with aaa (Freeradius).Freeradius receives the user and responds with an Access-Accept. According to the log, an IP address is also selected and is pa...
Cisco 4321 ISR running Cisco IOS XE Software, Version 03.16.01a.S - Extended Support ReleaseOn boot I get this error %FLASH_CHECK-3-DISK_QUOTA: Flash disk quota exceeded [free space is 1495100 kB] - Please clean up files on bootflash.So i thought i w...
Hi GuysI saw an ISP router interface the other day with a route tag applied to the interfaceipv4 address 192.168.1.1 255.255.255.0 route-tag 5 commandWould this have been a Cisco router? if so what IOS? I've never seen this command before on an inte...
