Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

in our mpls network we have ssm deployed for multicast, but for some old reason there is a static RP also defined on each box and as per my understanding it is not required incase of SSM. we are planning to remove the RP entry but after removing it f...

We have Cisco 7609 routers in our network. We are using ppp multilinks between the sites. Because of the high traffic volume, we have to use multiple multilinks. 7609 router doesn't allow ppp multlink to span SIPs, so we use multiple mulitilinks bet...

f-m-s-2000 by Level 1
  • 2877 Views
  • 21 replies
  • 0 Helpful votes

Hi, Now I am tring to setup Cisco 1812j with ISDN Line.Here is what I connect the device.(I am in Japan)ISDN Line (NTT east) >> DSU(NTT east INS Mate V30Slim with S/T port) >> Cisco 1812j(S/T)On DSU setting I enable DSU and Disable Terminator.First o...

Dear.I would like to know Is there any other useful tool for compare each routing table?because, we need to check the routing table. current backbone routing table and another routing table.Please let us know if there is tool which is to compare rout...

syjeon by Level 1
  • 994 Views
  • 0 replies
  • 0 Helpful votes

Hello, I am running the following configcloud -> ASA -> ROUTER -> LAN,I am doing NAT/PAT on the router instead of the ASA because I am bumping up against my 10 user license.Everything is working fine, but I am having an issue trying to get the asa to...

Hi All,I'm hoping the community can help me out with this one....I have a WAN connection to a site that is being brought into my network via MPLS.  The Service Provider and my edge router is using BGP.  The BGP routes are being redistributed into OSP...

jc84_ by Level 1
  • 2181 Views
  • 13 replies
  • 0 Helpful votes

Good Day Everyone,I am looking around the Cisco site for a table showing the Cisco router model number against the number of user supported.I have had a sales person ask me if an 1841 would support 20 users with the possiblility to grow to 50 and in ...

alalli by Level 2
  • 509 Views
  • 3 replies
  • 0 Helpful votes

Dears ExpertsHiCould  you help me to Install WAN NETWORKto  PLEASEMain Office ( HQ):  Cisco  Integrated Service Router 2811 1 Port Channelized T1/E1 and ISDN  PRI High Speed WAN Interface Card E1/GSHDSL Modems Cisco 2800  IOS firmware Branches :Cisco...

Dear all,I currently have a VWIC2-1MFT-T1/E1 card.This card does not allowed me to configure more than 2 channel-groups in my E1 port.I need to use a channelized E1 with 10 different channel-grous (10 different conections for branch offices).Ive read...

o_unzueta by Level 1
  • 839 Views
  • 2 replies
  • 0 Helpful votes

HelloWe got One ADSL 4MB Link terminated on 877, this router is the default Gateway for users. To have redundancy we plan to get another link 4MB ADSL link terminating on another 877 from a different provider. what config is needed to have auto switc...

Hi.I made following schema.ASA5505 + sec plus licensee0/0 -access VLAN2-> uplinke0/1 - trunk .1q -> switche0/2 - access VLAN9e0/3 - access VLAN9e0/4 - access VLAN9e0/5 - access VLAN9e0/6 - access VLAN9e0/7 - access VLAN9native VLAN was reassigned fro...

Need to configure 2 E1's for both voice and data. Also implement load balancing and QOS on them. Can someone help me to configure the E1's.These E1's are terminated on G703 card. The routing protocol is eigrp.Regards

SJ SJ by Level 1
  • 1137 Views
  • 6 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card