Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Webinar

 
Labels

Forum Posts

Hi,We have 2 cisco 1800 routers and we are running EIGRP , we have 2 mpls links for each routers how to configure one mpls link fails automatically takes2nd link for the productions --Like HSRPCan any one help on this for configurationsregardskrishna

hi to all! I'm a newbie at BGP, i would really appreciate some help....Here is my scenario: i have a edge router that connects to an ISP.  but this isp is sending me full routes that causes my router to experience high CPU utilization.  Ihave request...

I was informed by a colleague that the 001/8 IPv4 address space was just allocated to APNIC by the IANA.001/8    APNIC    2010-01    whois.apnic.net    ALLOCATED   What does this do to certain devices (some of our Cisco Wireless Lan Controllers for e...

We're using Cisco 2811's at branch sites. I need help with the QoS configuration on the Fast0/0 interface and also for the NM-16ESW. We're testing on a cable modem connection (yes I know this is not optimal) with 6 Mbps download and 512 Mbps upload...

Hello all,I've got a design question that I've been thinking about, and havent been able to come up with an answer.  I'm currently in the process of getting a full DS3 / T3 at one of our companies locations, and I'd like to allocation bandwidth perce...

Jkloza_2 by Level 1
  • 564 Views
  • 2 replies
  • 0 Helpful votes

We got L3 switches as core switches as end to end WAN link bet our sites. a Cisco 6500 on the other and a Cisco 3750 on the other end.Now we wanted to see the a real-time port traffic usage and don't know what cli command to use like of the "netstat ...

redrobish by Level 1
  • 491 Views
  • 2 replies
  • 0 Helpful votes

Hi All,           I have configured all of my E1 lines into multilinks . we do often video-conferencing once a week , in that case there are lot of drops on interfaces and tx , rx are also too  much. but i have checked that bandwidth consumption does...

Hi, I have one 2800 series router having inside address 10.10.10.10/24. I have configuration backup which I have taken from Putty.In the configuration, I have many md5 encrypted key like eigrp, hsrp, bgp & ntp. I do not want to connect this in networ...

Hi all – I am after some input on a configuration I am looking at.I have 2 x 3750Gs which are stacked, and 2 x 3130s (DELL Blade Switch) also stacked. Note they are separate stacks. I need to connect them, preferably using LACP (I think). So, I figur...

awelliott by Level 1
  • 2670 Views
  • 1 replies
  • 0 Helpful votes

Hello Everyone,I don't know if I'm in the right section..But, would like to double up on our 7609 Supervisor Engines.Is there a procedure somewhere on the Cisco Website that can help me prepare for my activity?orIs it an acitvity that shouldn't have ...

Mavrick25 by Level 1
  • 3863 Views
  • 11 replies
  • 0 Helpful votes

Dear All,I have 2 cisco 2821 routers with internet connections from differents isp, they are connected to a cisco switch on which 2 ASA 5510 are also connected.Behind the firewall, there is another switch for lan users.I can achieve redundancy by con...

kolawole1 by Level 1
  • 506 Views
  • 2 replies
  • 0 Helpful votes

Hi  expert,       On gns I was doing a practice , but I am not able to ping firewall otside interface from router connected to firewall inside interface.      1)  Nat-control is not enale so nat statement is not required.      2) I enable icmp in glo...

It's my understanding that unless there's a point-to-point link, you're supposed to specify an IP as next hop when doing static routing.There's a static route on our VPN3000 concentrator that points to the private interface as next hop, instead of th...

huangedmc by Level 3
  • 1832 Views
  • 3 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card