Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! Trouble with upgrade IOS on 7206vxr

I am not sure what I am doing wrong so hopefully someone will see my bonehead mistake.Here is the issue:MONEXTR01(boot)#copy tftp bootflash:Address or name of remote host []? 10.1.1.240Source filename []? c7200-adventerprisek9-mz.124-24.T1.bin ...

BGP Questions

Hello ,I am trying to setup BGP between our primary isp and the backup isp . We have our own AS number and a netblock that we would like to advertise . I would like to setup BGP in such a way that i will be advertising a /24 bit route to the BGP clou...

Resolved! loopback address for 2960

Hi,For the router devices, it is suggested to configure the "loopback interface" for keeping router working stable.For the L2 switch, is it the best practice to configure the loopback address for achieving the same purpose?rdgs

Cisco IOS vulnerabilities 09/08/2009

I am using IOS release 12.4(15)T9 c2800nm-advipservicesk9-mz.124-15.T9.binAccording the Cisco vulnerabilities release notes:http://www.cisco.com/en/US/customer/products/products_security_advisory09186a0080af511d.shtmlDescription: Multiple Cisco produ...

cisco24x7 by • Level 6
  • 517 Views
  • 2 replies
  • 0 Helpful votes

DNS forwarding in L2 switch

1. What are the commands to resolve the public DNS from switch? Even if public DNS added in switch with ip name-server commands.2. How the DNS to be resolved in two seprate networks? 192.168.1.0/24 & 172.16.1.0/243. The Network is: Internet-ADSL rout...

pp1326mah by • Level 1
  • 685 Views
  • 1 replies
  • 0 Helpful votes

Resolved! duplex mode on serial interface

Hi,I have a simple question. How can I configure and show duplex mode i.e. full or half duplex of serial interface which is running PPP or HDLC? Could anyone please advise?Thanks,Nitass

nitass by • Level 1
  • 7294 Views
  • 6 replies
  • 0 Helpful votes

Router Logs

Hello, We have monitored some logs on our cisco 1700 series router. FIRST LOG :---------------On executing "sh int Serial" command we are getting output, where last line is.DCD=up DSR=up DTR=up RTS=up CTS=downI guess CTS=down means there may be s...

cisco.net by • Level 1
  • 396 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Stacking (Router and Switches)

HiI am trying to understand "stacking". Lately I am hearing a lot about stacking and I dont know when do one should consider stacking and how it is done. I read about switches (3750) being stacked and lately I have a document that requires me to test...

MGX 8830/B with 2811 routers

Hi,I have two MGX8830/B with PXM1E. VISM-PR-8E1 and MPSM-8T1E1 exist in the MGX with backcard RJ48-8E1 each. I have two 2811 routers with AIM-ATM and one E1 card each.Now i want to connect both these MGX in a manner given below. R1 <-> MGX <-> MGX <-...

Resolved! bgp into eigrp redistribution

I have my wan router set to redistribute its eBGP learned routes into eigrp, which is then communicated to my 4510, and my 4510 then communicates those routes to my ASA. This is done mostly for backup purposes, which allow longer mask and shorter ma...

Reflexive ACL behaviour

Hi friends,A basic doubt.I am checking REFLEXIVE ACLs. During Lab i found this behaviour.152.50.12.1 (R1)-----(R2) 150.50.7.7where 150.50.12.1 is untrusted & 150.50.7.7 is trusted.Reflexive ACLs are configured and working perfectly as expected. When ...

Load more