Hi guys,I just found this on FAQ, do recent IOS support bridging for GSR?Thanks.Jeff
Hi guys,I just found this on FAQ, do recent IOS support bridging for GSR?Thanks.Jeff
Hi....I have two locations say "A" and "B"And I have two 30MB lease line between these two location.I want to configure Eigrp between two location.I know about link failure using eigrp but can somebody tell how can i achive load balancing. "A" ------...
I have 3 routers in three areas.R1 ---> Area 0R2 ---> Area 0 and 1 (ABR)R3 ---> Area 1. R2 is connected to R3 (in area 1)through a FR,with 'ip ospf net point-to-point' configured. I try to filter inter- area routes from area 0 from entering area 1 by...
Hello ExpertsMy home broadband has just been upgraded to ADSL2 and my cisco 857 doesn't recognise the ADSL line anymore.Its got 12.4(6). The wan interface is reads ATMoPOTS.Some forums say that the Firmware needs upgrading. Some say the IOS needs upg...
Hi, Ã would like to know if i have to set the speed at the fastethernet of these 2 equipments, or keep them in auto negociation. Thanks.
Hi I'm having a problem establishing a stable GRE tunnel and was wondering if anyone could help?Both Routers are 7200s. RouterA is running IOS rev 12.3(4r) and RouterB is running IOS rev: 12.2(5d). Both sides of the tunnel show as UP/UP until I enab...
Could anyone provide any assistance in relation to the following error we received on one of our 3550s. I've searched both Cisco website and the Internet in relation to the exception code but there doesn't appear to be any documentation related to it...
Hi to all,i want to know if the 3g interface must be used only for data connection or can be used for route voice call to cellular network.
We have a "smart jack" installation that connects to our router. The cable going from the smart jack to the router WAN interface seems to be a CAT5e cable with RJ-45 connectors at both ends.Most network diagrams in training materials represent T1 Fr...
Have 2 offices connected by a 2MB fiber connection. Cisco 1720 and 1721 on each end. Office 1, 10.147.28.xxx, Office 2, 10.223.112.xxx network. Recently users on the 10.223 network would run an RDP session to a terminal serve ron the 10.147 networ...
What is the advantage of using BGP? Why would I need to know all routes on the Internet when my ISP knows that? Isn't that what I'm paying them to provide (access/routing on the Internet)?I ask this question to stimulate discussion and to further u...
I'm trying to create a bundle using 3 x DS3 on a 7206 in order to have a backbone link that is larger than 100Mbps. Due to the limitations of MLPPP I cannot do this using a multilink bundle when the DS3's are clear-channel and these cards are not PA-...
I would like to load balance between our MPLS circuit and IPsec tunnel. Preferrable solution will be to load balance after MPLS circuit reaches 80% load of the bandwidth. I understand that AVG responds the ARP for default gateway IP address, now how ...
Hi All,I have the cisco switch WS-C4948 running IOS 12.2(46)SG and local span session configured:sw-4948>show monitorSession 6---------Type : Local SessionSource Ports : Both : Gi1/5-11,Gi1/21Destination P...
Hi I am facing problem related to OSPF I am runing OSPF between 6 routers in area 0 with bfd supportfor testing purpose i have executed shut command on one of the interface as expected teh OSPF stae changed to FULL To DOWN, but when interface made no...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-26-2025 02:24 AM | ||
| 10-24-2025 11:24 AM | ||
| 10-16-2025 11:52 AM | ||
| 10-15-2025 06:33 PM | ||
| 10-15-2025 04:37 PM |
| User | Count |
|---|---|
| 4 | |
| 4 | |
| 1 | |
| 1 | |
| 1 |