Routing

Hi, I am confused with WCCP direction. I have L3 switch. Content device is attached on E0/0 & desktops are connected on other interfaces,like e0/2, e0/3. Please help me about commmand "IP WCCP Web Redirect OUT/IN". IN direction will on E0/0 where Con...

Hello,I have dial back up configred on 871 with parameters below.871 Conencts to an AirLink Raven box which provides fixed wireless broadband.=======================================track 10 rtr 1 reachability delay down 70 up 70ip route 0.0.0.0 0.0.0...

Hello!After power off Cisco 877 erase startup config. This is output from console:"Erasing the nvram filesystem will remove all files! Continue? [OK] Erase of nvram: complete Router IOS Configuration Recovery is unsuccessful"After that it reloaded wi...

Hi all! This are my nat staments, ip nat inside source list 111 ROUTEMAP_NAT pool publicips ip nat pool publicips 1.1.0.1 1.1.0.254 prefix-length 24 acess-list This is a pool of 254 IPs but i have 500 host, if the 500 host try to access internet at s...

I am having issues with horrible performance on my WAN with several sites. My provider tells me that they are seeing my router recieve from the WAN at 100% utilization for about 5-10 seconds every 40-50 seconds. My MRTG and Netflow don't tell me mu...

Hi, I have three switches SW1,2 & 3, they are are connected with Trunk ports. I have Router R4 & R5 which is connected with these switches as following-R4(e0/0)->SW1(f0/0)& R4(E0/1)->SW2 (f0/0)R5 (e0/0)-> SW3 (f0/0)R4e0/0 is in Vlan 54 & E0/1 is in V...

Hi, I have to limit WWW Syn packet to 500Kbs. I am confused by CIR, be & be has been choosen like following --access-list 192 permit tcp any any eq www syncint f0/1 rate-limit output access-group 192 496000 4000 4000 conform-action permit exceed-acti...

Dear All,I have recently joined a small ISP which provides Wireless Broadband to customers using Motorola Canopy products.In the attached diagram I have explained the current setup to provide wireless broadband services. So let me explain how current...

HelloHas anyone tried to change an access link, carrying live traffic, to a trunk.I need to do this soon and would like to learn from others who have experience with this - is there a procedure out there or steps I can follow?This currently carries t...

Hello,We currently have a 2811 router with two 2 port T1 WICs. These are configured in a single IMA group as a 6Mb internet circuit.We would like to double our capacity by adding two more 2 port T1 WICs. From my reading, we can't create an IMA group...

HI first of all, the system log like below:Jun 18 08:59:28 c_kc2 4577: Jun 18 09:42:17 KST: %FIB-2-FIBDISABLE: Fatal error, slot 8/0 (8): CEF-Common: no memoryJun 18 08:59:28 c_kc2 4578: SLOT 8: Jun 18 09:42:17 KST: %SYS-2-MALLOCFAIL: Memory allocati...

I am having issues with getting an etherchannel between a 2821 (on-board giga ports) and 3750. I have followed the config shown in the Cisco docs but can not ping the devices, and when I do a Show etherchannel command on the 2821 no ports are shown a...

Hello All, I am in a bit of a confusion here. I am planning to implement dual gateway implementation to avoid single point of failure. Now I have HSRP and STP running on couple of 6509 which help with the l3 traffic for the intra site. Now t...