Hai friends,I am having a router with WIC-2T card and having the connection with a v.35 cable.how i can check the port is working fine.Any support documents for the procedure for testing that port.
Hai friends,I am having a router with WIC-2T card and having the connection with a v.35 cable.how i can check the port is working fine.Any support documents for the procedure for testing that port.
HiWhich card with 1 or more interfaces DS3 I need for a router 7206VXR?.
I have an issue where one locally connected network is not being advertised by BGP. All the other networks are working fine. Would the "clear ip bgp soft" command work possibly?Non-working network:router1#show ip route 10.xx.x2.0Routing entry for 1...
I have a question about using static routes with DHCP.I understand that a static default route pointing to an interface, as the next hop, will generate superfluous ARP entries for every destination. So, with that in mind, will the static route (A) be...
Greetings, Router BGP is redistributing an OSPF instance. The OSPF instance carries a 10.10.10.x/24 and 192.168.10.x/24 networks. Do I need to specify both networks in bgp? For Example router bgp 65000 network 10.10.10..0 mask 255.255.254.0 network 1...
I have the following username and password on the same router:username admin password adminusername Router2 password pppchapI want to use "admin" for local authentication to console and VTY (login local), and use Router2 for PPP authentication (ppp a...
Hi All,I have configured MPLS QoS in a 1841 PE router. F0/1, which is connected to CE, is marking the traffic; F0/0 is doing LLQ. But 'show policy-map int f0/0' shows packets matched but no marking is done for 'mpls experimental topmost X'. So I add ...
I have a 3725 with a T1 connection that terminates into a channelized DS3 on a 7200.The 3725 sends and recieves the multicast EIGRP messages with no encap failures (verified with debug IP packet that it is sending, and the addition of the 7200 into t...
I am not sure if I am in the right forum.We have an installation that suffers constant and long periods of power failure - more than a normal and good-priced no-break can solve.We are thinking to use an IP traffic redirection. Is it possible: in a po...
I have configured eigrp between 2 routers.rt#1network 10.10.10.0network 172.16.1.0no auto summaryrt#2network 20.20.20.0network 172.16.1.0no auto summarywhen i do show ip route on both the routers. It gives the following output,rt1# 10.0.0.0/8 is ...
i am using the below formula suggestes by cisco for calculating policing parameters like bc,beCIR in bpsbc=(CIR)/8 * 1.5be=bc*2So the above formula we are following it for 1G interfaceswe are seeing the maximum allowed bc bytes as below <1000-5120000...
I am getting this message in the log every 5 min "RTR responder null keyPtr, id= 1" The error message decoder says not found. Any ideas what this is?
Hi All,I have a question about what's really the difference between a synchronous serial interface and a asynchronous serial interface on a router? When would you use one or the other and if the difference is physical or just in configuration.Thank y...
Hi all,I have loaded the "s72033-boot-mz.122-33.SXI.bin" file in the 64MB bootflash of Sup720. I also specified the bootvar to boot it from this location and file via boot command. However, every Sup720 reboot returns to ROMMON mode. Why is that? ...
I'll be deploying this solution:1 ASA that terminates VPN from a few remote sites1 2821 with two ADSL Annex M (SDSL) WIC'sWhen both Internet Accesses are working, i want to send all vpn traffic through one of them, and the internet traffic to the oth...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-09-2025 12:02 AM | ||
06-08-2025 07:22 PM | ||
06-06-2025 12:18 PM | ||
05-28-2025 01:50 AM | ||
05-15-2025 07:28 AM |
User | Count |
---|---|
8 | |
4 | |
3 | |
3 | |
1 |