Hai ,In one interview this qstion was asked ..how do we choose a appropriate routing protocol for a network ....y ospf y bgp etc ..can some one help me in clearing this thank in advanceujil
Hai ,In one interview this qstion was asked ..how do we choose a appropriate routing protocol for a network ....y ospf y bgp etc ..can some one help me in clearing this thank in advanceujil
hi guys,There's something in Cisco's BSCI Exam guide, 4th Ed, on page 350 (Example 2).Routers B, C and D are supposed to see both RIP and EIGRP routes, right? On page 352, the configuration 's output shows that we redistribute EIGRP into RIP.I don't ...
i inherited a network that is redistributing routes from BGP to EIGRP and back again. I get a queasy feeling everytime I make a routing change. I want to clean it up (and make the table smaller) by announcing summarized routes via BGP to remote si...
I can telnet to the roouter from any port on the router , but I can't telnet to the loopback.. yes there is user and password . but its the same as for other ports , any help pls
Hi,Is it 3845 router supports 100 meg internet pipe.Thanks,Mahesh.
Hi,I just have an inquiry regarding the capabilities of these routers. We are planning to use our existing routers for voice. Currently, we have plenty of 3725 routers with NM-1A-T3 each. We would like to know if this can also handle NM=HDV network m...
3725 with 12.3(7)T and VWIC-2MFT-T1. Two T1 lines set up in multilink ppp configuration to aggregate bandwidth. Controller T1 0/0 set up with channel-group 0 and controller T1 0/1 set up with channel-group 1. I am confused about channel-group config ...
HelloWe have a problem with our ospf configuration.We have two area :area 0 is the wan areaR2 - R1 is the major tunnel linkR1 - R3 is an adsl spare tunnel linkarea 1 is the local area R2 R3 R4 are on the same local network.Other lan network are behin...
When using SPA with SIP for implementing Router Interfaces we can reduce cost of investments, but what can be lost when using this model in comparison with using Line Cards.
Hello,I have a WAN and I have two routers one in the UK and one in the states and I'm running OSPF. When the two routers neighbored everything in the UK got routed through the US which is fine except for certain traffic. I've put in static routes bu...
When using SPA with SIP for implementing Router Interfaces we can reduce cost of investments, but what can be lost when using this model in comparison with using Line Cards.
I have a neighbor bgp with my mpls provider. In some cases the number of prefixes that I receive is different that the number of prefixes that they advertise.For example:In the ISP's router:sh ip bgp vpnv4 vrf xxxxx neighbors 77.3.220.26 advertised-...
I have a Cisco 3640 router. On this router I have 12 serial ports and 1 fastethernet port.Only 6 of the serial ports are active, the others are shutdown. 2 of the 6 are connected to T1's to the same router on the other end and configured to load-bala...
Hello,I am setting up a condo with a Cisco 3640 and a 200 port DSLAM. Currently it would take 6 months to get a fiber link to the building (no fiber in the area). We would like to get the place up and running fast and opted to install multiple ADSL...
Hi All,I was wondering if anyone might be able to help me through my conundrum!I'm trying to configure a 1801 router to fail-over between a main connection, via the fa 0 port and a backup via the ADSL port. I've been able to achieve this with the att...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-09-2025 06:19 PM | ||
02-06-2025 12:03 AM | ||
02-03-2025 09:24 PM | ||
02-03-2025 07:43 PM | ||
01-13-2025 09:53 AM |
User | Count |
---|---|
16 | |
10 | |
8 | |
8 | |
4 |