Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Bookmark
|
Subscribe
|

Labels

Forum Posts

Hi,I want to add layer 3 router interface on C2851. I did a search and find the following part number"HWIC-4ESW Four port 10/100 Ethernet switch interface card My quesions is:Will the 4 ethernet ports share just one layer 3 interface or they are 4 se...

yuhuiyao by Level 1
  • 1871 Views
  • 6 replies
  • 0 Helpful votes

Greetings All, What is the recommended EIGRP holdtime value on GRE tunnels. I have a backup link using ipsec/gre that goes thru the internet. Earlier today we had an outage that caused us to use our ipsec/gre internet backup link. Everything would ha...

merryllem by Level 1
  • 636 Views
  • 2 replies
  • 0 Helpful votes

We have layer 2 connectivity from our main office to an offsite facility where our servers reside. We are connected via fiber but is not a dedicated circuit. Recently I created a VLAN with same ID on both switches (main office and Offsite facility) ...

Johnramz by Level 1
  • 326 Views
  • 1 replies
  • 0 Helpful votes

Hi,I have a C2610 router.I issued "erase startup-config" and reloaded the router and after this i am not able to make the router boot. it is going to ROMmon prompt.I also checked the article in : ROMmon Recovery for the Cisco 2600 SeriesRouter and th...

vikrant by Level 1
  • 1418 Views
  • 5 replies
  • 0 Helpful votes

Resolved! Ipsec site to site

Hi,Am using Ipsec between two Routers (site to site) in lab environment for testing. . The Router A local LNA is not pinging to remote Router B and crypto section is showing down. Please provide the solution for making up this scenario.The detailed ...

I have two /24s that I am planning to announce: 216.54.xxx.0/24 and 165.17x.240.0/24. My plans are to advertise both subnets from both of my ebgp routers to both of my ISPs. The 216/24 is owned by provider 'A', and the 165/24 is a direct assignment I...

Hi,My customer would like to encrypt traffic across all our private P2P circuits. We have a hub-spoke topology with 50 spoke routers per one hub router. After some searches, I narrowed down to these options:GET (Group Encryption Transport): This is...

kevin.hu by Level 3
  • 603 Views
  • 4 replies
  • 0 Helpful votes

i have a 100Mb ethernet WAN connection between two sites. I'd like to calculate the throughput. I was trasferring some a 50Mb file over the link and only getting 70,000 bytes per second.

Tshi M by Level 5
  • 613 Views
  • 5 replies
  • 0 Helpful votes

I have a Cisco 1841 in my Network which is acting as a Gateway. It is connected to the outside world on a low-speed serial interface (The Router has 2 low-speed serial interfaces, 1 ethernet and 1 VPN port). I always get a slow connection over the ne...

uzmausmani by Level 1
  • 2387 Views
  • 11 replies
  • 0 Helpful votes

Hi Friends,I am going through a document on Cisco WAAS (http://www.cisco.com/en/US/docs/app_ntwk_services/waas/waas/v407/configuration/guide/SNMP.html#wp1106982) I would like to know what all things can be monitored by using WAAS MIB. I fail to under...

Hi all,i have my one client who is accessing internet through satellite, currently they have deployed HUGHES product, i want to replace it with Cisco, can anyone suggest which product to use.And also can IP-VSAT module be used with ASA5510 series or ...