Routing

Hi Sir,I am config a Cisco 3845 router ios version 12.3(11r)T2. This router current have a AIM-ATM-4E1 connect to WAN. When I plug in the card NM-1A-E3 into the router. The E1 connection will lose (ATM0/IMA0 will up and line protocol will up but the ...

Hi,We are using two ISP A and B, I want to send the HTTP traffic via ISP A and mail SMTP traffic via ISP B. Would you please let me know the simple configuration for this concept.As per the attached fig.

Due to EOS / EOL issues, we need to move off of a multiple 7401 strategy for our WAN edge. We need to support up to 6 DS3's from various carriers. Any recommendations for a redundant consolidated platform ( 1 or 2 big boxes)vs. multiple single boxe...

why we configure default-gateway on a switch ? Can someone give an example ? As i know switches makes forwarding decisions based on layer 2 ( i mean layer 2 switches).

I was wondering if anyone knew what the maximum amount of traffic that can be passed over GRE tunnels for this sup. I seem to think that it is 35Mb, but not really sure. Also can I add an ASIC daughter card to improve this?

i have a network where in i have one ebgp ckt through a provider to my remote locations & also have a IBGP connection to my remote sites through point to point ckts, now i want to have redundancy as well as load sharing across these two exit points o...

Hello all,Would like to know whther the below setup works ??Primary connection :Site C connected to Site B ( point-point)Site B connected to Site A ( point-point)Secondary connection:Site C connected to Site B (ISDN)Site B connected to Site A (ISDN)N...

objective;copy active devices config thru TFTP from a remote PCscenario;pc----6500lanA--sdh ring 1.....6500lanG6500lanJ----sdh ring 2---6500lanZ- lanA 192.168.1.x on vrf- lanZ 10.10.10.x not on vrf- there are core switches on each of the major locati...

Hi all,1. If the local router receive full routing from ebgp peer. How can I filier it to receive only one default route instead.2. Suppose my bgp router connect two ISPs. How can I config local router to avoid to become Transit area.Any document men...

Hi AllGetting intermittent failures using a 1760 router with 2 adsl wics.Looks to me line like one of the lines has a noise problem? Perhaps someone could confirm this for me?sh dsl int atm 0/0ATM0/0Alcatel 20150 chipset information AT...

Hello,I have a private network on 10.0.5.0, with a Websense server on 10.0.5.20. All client machines on the lan use 10.0.5.20 as the default gateway and dns server. The websense server also has another network card with address 192.168.0.2, and the...

Hi,I setup the remote office. It is cisco 871. How do I config the VPN between remote office and central site? any VPN sample config for cisco 871? Thanksrdgs

I need to create a VRF on a Bastion router for management..can someone direct on how I should proceed? I have a physical connection to the Bastion switch and I am not sure how I should proceed with a VRF to only allow the management vlan to be seen.....

My perimeter router is connected with my branch over a leased circuit and remote branch network appears in routing table as OE2, my floating static route on perimeter is installed and pointing towards ISDN interface with the AD of 200 and redistribut...

Clocking with multiple connections.I need some help on figuring out how I should setup clocking in the below scenario. In back of this router is UCM Business Edition.Customer has 2851 with four vwic-mft-t1's (only three in use) and one NM-1CE1T1-P...