Hi I'm a little rusty on IOS-XE software updates and looking for some advice Please see below outputs, I dont recall seeing the system image being the packages file on any ISR's I've logged into before, but it has been a while. Normally I see a speci...
Forum Posts
Hello, I am tasked with having to connect a whole new ISP to my already existing LAN during a change over. The sites are constantly feeding information and on a VRF (10.0.1.2 & 10.0.3.2) Which means, my old ISP pathway must remain online until all ...
HI - I was hoping to get some guidance on what my issues may be. I apologize ahead of time if i do not give enough info but i am new to the world of Cisco. I know enough to get by so i will do my best.I am trying to setup VLANS in our environment and...
Hi ! I have a Cisco CGR-2010/K9 that shows wrong miliamperes readings when I use show interfaces transceiver detail Do you know the root cause of this issue? Is this a normal behavior? Thanks in advance!
Hi,Short and simple question just to clear some doubt.Is it possible to advertise a VRRP/HSRP virtual IP over an IGP such as OSPF? Or is the only way to reach this IP by configuring a static route to it?Thank you.
Resolved! CSR1000v configuration 3 ISP
Hello! I cant find information about CSR1000v configuration multi ISP. I have requirements in project that i need to load balance 3 ISP, and router have to be virtual. So maybe someone have expirience with configuration 3 ISP on cisco CSR1000v?
hi guys,I'm depressed, I can't get a working tunnel... I've tested everything I can, read docs, posts, etc... but it doesn't work.I need to extend my Vlan105 from the HQ to a remote site. Here is my setup : PC [Fa] <---> [Gi] Cisco 2960-X [Gi24] <---...
Resolved! "d=255.255.255.255 (nil)" result in PBR
Hi, I'm having some other open post that still running for another aspect of the issue. Here I want to know what is this issue : I'm having policy based route from Group-A to Group-B I've run the command debug ip policy and I'm getting some strange r...
Hello!First of all clarify that I'm quite new with networks and I'm using web interface, no console. I have read some other posts but are for Switchs or differents scenarios.Im trying to config a Cisco RV345 with 2 VLANS.At the moment I have:- VLAN 1...
Good Afternoon All,First off, my apologies if this subject has been touched on before, but I'm relatively new to Cisco and the OS, and just finding my feet - I'd appreciate some help with the below.I've recently had a leased line installed from BT, a...
Hi ,I have bought a C921-4P router with IP Base License , but i come to know it does not support Mobile IP Protocol. Commands for Mobile IP configuration such as given below are not working.ip mobile home-agentip mobile virtual-network 10.0.0.0 255.2...
Resolved! PBR seems to be not implemented
Hi Guys, It's probably going to be long, but it's something that is very important for my team. We are working in company in few Lab's environment that is connected to IT. Our Gateway for all labs is currently 2 old 6500 working with VSS. Each lab is...
Say I have two ospf routers in Area 100: R1&R2 and the area is configured as NSSA. R1 also connects to the Area 0 which makes it as the ABR between Area 0 and Area 100. Within NSSA, I have some static routes redistributed into OSPF on R2. These redis...
Resolved! cisco 4331 ISR
hey,acually i am going to deploy i new cisco ISR 4331, this last should support 4 Link point to point with 512 ko as bandwidth, so i'll insert two NIM-2T catres.is that possible without any issue ?? does the router support those links normally ??than...
Hey everyone, Before I go into whats going on I want to make it clear that I am not very experienced with this stuff. I have taken CCNA parts 1 & 2 in a classroom environment, have not finished 3 & 4 nor gotten my actual CCNA yet. Thats pretty much t...
