Hi,I have configured a l2vpn tunnel & i want to pass the lacp packet through the tunnel. anyone can give me the command for cisco NCS540(XR ISO)? XE command is :encapsulation defaultl2protocol tunnel cdp stp vtp pagp dot1x lldp lacp udld loam esmc el...
Forum Posts
Resolved! I need a static route help
I need a static route to be able to ping Loopback0 on R2 from R1. I do not want a default route but something more specific pointting to the loopback address or subnet. I want to save the default route for something else. I dont wan't this by inject...
Config R2 to block 30.1.1.1/8 make sure R2 do not intsllat in its routing tablewhy & how "ip prefix-list INK permit 0.0.0.0/0 le32" used here ? why 30.1.1.1/8 prefix is not used ? can any one explain
Resolved! routing between bgp ASNs
Hello everyone, I have the network diagram as follows. As r-1 advertise its loopback 0 into BGP, i need this prefix to be reachable from r-5 and r-6. Same for r-2.now, i would like that ASN 1.2 to see only those 2 prefixes coming from ASN 1.1. Now i...
We are migration our Internetrouters from IOS based to IOS XR based Boxes. I need a translation of the following Route Weigth Policy to IOS XR My IOS Configuration looks like router bgp 30neighbor 10.100.83.1 remote-as 100neighbor 10.100.83.1 ebgp-mu...
Hello,Is there a command to auto calculate the OSPF path to a destination prefix from the originating router. I know you might say just check the cost in the routing table, but when I do that it doesn't give me a clear representation of load balanced...
HI, i am looking to configure QoS on a customers 4331 ISR. Basic 'router on a stick' setup with a basic Ethernet port-channel configured on three 1G interfaces. Port-channel contains about 10 dot1q sub interfaces. The policy I'm looking to config...
Resolved! Trouble with RIP routing
Hi, For the last hours i've been trying to implement dynamic routing on my workspace and kept running into the same problem. I've created the routes, but for some reason they dont show up when i try the command "show ip route" and can't ping from o...
Hi every one , i have 100 Mbps internet access and more than 5 subnets , i want to divide bandwidth between subnets or for each ip in subnet, i have 2951 cisco router , can any one provide me with the method of bandwidth limitation . with regards
From what I read in the 250 CCNP ENCOR book it says this page 157: EIGRP supports unequal-cost load balancing, which allowsinstallation of both successor routes and feasible successorsinto the EIGRP RIB. EIGRP supports unequal-cost loadbalancing by ...
Resolved! Router Certificate Question
HiHow do I renew Router Cert do I have to go through the full Enrollment process again and define the trustpointor is there a command to renew the cert as the trustpoint already configured.?? Thanks
Hi,I'm currently building a network and I'm not used to a design with Multilayer-Switches and Routers together in one network. My default interfaces for the vlans all reside on the two Multilayer-Switches made redundant with HSRP. Now I want the netw...
Hi, in some of the router of our network we have a policy that should guarantee that traffic marked with a certain CoS Value has a CIR of 80% and a PIR of 100%. Looking at the policy however, I cannot see how it can do that, people have assured me it...
Resolved! VLAN Bridging across multiple sites
I have 4 sites as seen above. Each site has the same VLANs A,B,C and D. I would like to bridge these vlans across all sites so that each of the VLANs appear as a single bridge domain across all 4 sites. I have explored the possibility of using L2TP ...
Resolved! BGP values
I am studying about BGP and I looking for information about these values SRTT: X ms, RTTO: X ms, RTV: X ms, KRTT: X ms What they are used for? And what are their meaning? Tks, Maverick0
