Can the 3745 router support an OC-3 circuit and if so, what blade would be used to do so?
Can the 3745 router support an OC-3 circuit and if so, what blade would be used to do so?
hi I am facing a problem with PIX 520 ,i have connected it with consol but it did not work ... could not get display.I have study on cisco site that it will boot with flopy drive .. but i have nt its flopy ... m i right ????wht could i do ???? how ...
On a 2950 port 48 is in vlan 66, switchport mode access. This is connected to Intrusion Detection Device and that in turn passes back to a second 2950 to port 39 which is in vlan 137. The two 2950s are connected with GBICs in trunking mode. Also p...
HiWhen I configure an area as a stub it works just as I would expect, ie I get type 3 and 4 LSA's and also a default route. But if I configure an area as an nssa I only get type 3 /4 LSA's, I dont see either type 5,s or a default route. To get a defa...
Good Morning,I need to implement a roting scenario with a Cisco Router with 3 FE interfaces. But i did not found a 2800 series with this caracteristics. Can I use a HWIC-4ESW to resolve this problem? (because HWIC-1FE is in EOS, it is true?)ThanksPa...
This is a routing question. I have seen this before on routers and on firewalls. Can someone explain why this happens or how I might go about debugging this?We have a data center and part of the diagram is below.We have a server that has to go thro...
will 3600 router cards work in a 3800?
My customer wants to implement multilink ppp using E1 belonging to different carriers. Before doing that I want to know if it is possible?. Are there any restrictions, warnings, requirements?.
Hello.I am needing some advice on how to setup the following.I have in the field T1 connected to a MPLS network coming back to a T3. The T1s are conjested with Lotus Notes, Oracle and Voip traffic. The field routers are 2821 with Call Manager plus t...
Hi,I have a 1811 router which is crashing at seemingly random intervals. Each time the router creates a timestamped crash file.-Are there any tools that will allow me to see what the cause of these crashes might be?-How can I know if the image I have...
Please correct me if I'm wrong. If i use the following commands, the following actions are supposed to happen:1. The iBGP is allowed to be redistributed into OSPF2. Because of the route-map, only the route to 131.189.0.0/16 will be redistributed into...
I have currently two routers connected to the same ISP, using peeing via BGP.The routers then run HSRP between them for the internal network, so I one fails the other one takes over, there is no BGP peering or other routing protocols between the two ...
Hi all,We currently have two sites (A and B) with a private 20Mbps link between sites. Our primary Internet pipe is located at site A (Pipe A). We do have a secondary pipe at site B (Pipe B). We're using EIGRP to redistribute routes, including static...
Here is what I am trying to acheive. I am trying to using multiple IP's that are allocated to me to control SSL connections to multiple sites. Router - Cisco 871IP1 - 72.29.239.xIP2 - 72.29.239.yI am trying to redirect traffic on 72.29.239.y to a ser...
Due to some reason, I need to redistribute one route leart from BGP into OSPF, in order to let the hosts in my network know this route. I use the following commands.router ospf 17357 router-id 216.x.x.10 log-adjacency-changes redistribute connected s...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-05-2024 05:56 AM | ||
10-04-2024 06:22 AM | ||
09-23-2024 06:56 PM | ||
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM |
User | Count |
---|---|
13 | |
11 | |
6 | |
4 | |
4 |