Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

2 Adsl service on 1 router ,for MPLS and VPN

Hi, our company currently connect a C2811 to MPLS through ADSL.there is another cisco 837 adsl router, which isnt connect to the Mpls.we would like to have another adsl service on the 2811 router with a static public ip, so that we may able to settle...

Router is not booting up

HI, i have 7206 router and 2 IOS has been downloaded in disk0. The IOS's are 12.2 and 12.3 but it was using 12.2 IOS.When i tried to boot the 12.3 IOS using boot system disk0:filename and i restarted the router but now the router is not coming up. Ca...

Dialer-watch behaviour..

Im experiencing some (strange?) behaviour with a dialer-watch setup I have running on an 1801 router.I have an ADSL service backed up by an ISDN service.Essentially the failover works fine, but the problem is with the "failback" to the ADSL service w...

Resolved! OSPF and VLANs

I've got 2 2620s connected via a point to point link and running OSPF. In one location I've got 2 VLANs, one for voice and one for DATA. I need to route or bridge those to the second location, as I am putting phones there as well.Do I just use a BVI ...

bregimand by • Level 1
  • 2014 Views
  • 9 replies
  • 0 Helpful votes

2610 Router with Multilink Frame

I have a 2610 with 48 flash, 16 ram and I'm trying to configure it for Multilink Frame and I'm having a problem determining the IOS I need for it to support it. When I go into the Interface mode I don't see MFR, I was wondering if anyone knew if it ...

cisco IOS error

I have this error when I start my router System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1) Copyright (c) 2003 by cisco Systems, Inc. Bad RAM at location 0x00000000: wrote 0x00000000, read 0x00000400 Which is the problem? How can I...

NAT incoming from internet but not VPN Tunnel

I have my router setup with 2 NAT commands to forward traffic coming in on certain ports to 2 different servers based on what the port number is. I have this setup so I can VNC into the servers remotely. ip nat inside source static tcp 172.16.0.17 ...

Policing traffic

Hi I have attached our network diagram. We have a server at one location which is basically collecting logs from all the other locations and hogging all the MPLS bandwidth. I want to implement policing and restrict the bandwidth for the particular IP...

OSFP - VRF-Lite - Question

Hi, A brief VRF-Lite question, I want to build a redundant setup using VRF-Lite on some Catalyst6509's, where I want to use OSFP as the IGP, and redistribute it into BGP, for uplink to our edge..Some time ago, I heard that there where a limitation on...

Routing Traffic to Different Locations

Right now I have two locations tied together through two Cisco 1720 Routers. Between them is a T1 Line. As of right now, I believe there is a route set up in one of the routers that allows all port 80 traffic to be directed to our firewall at our oth...

Accessing file shares behind router using NAT

I am trying to access a file share behind a router where I am using NAT.I have created a static 1 to 1 translation for the outside to the inside address so all other traffic like RDP (Terminal Services) works fine but I cannot get a file share like \...

Load more