Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Resolved! Radius Source

I have several routers with backup links and we use Radius for authentication into those routers. It seems like the Radius uses the primary serial link to connect to the Radius server. When the link fails and it switches over to the backup I can't ...

jobegates by Level 1
  • 2260 Views
  • 6 replies
  • 0 Helpful votes

Dear all, We have a router where leased line is primary link , VSAT is secondary & ISDN is tertiary link. VSAT has output in form of ethernet which is terminated on L2 switch . Whenever leased line goes down , traffic gets shifted on VSAT but proble...

amansoi_5 by Level 1
  • 488 Views
  • 4 replies
  • 0 Helpful votes

Hi AllThis morning I performed a password recovery on a cisco 827 router. Since then i have not been able to keep changes I make to its config. Could I have done the password recovery wrong ? At the time of recovery I did not know the config-reg s...

dborg by Level 1
  • 411 Views
  • 2 replies
  • 0 Helpful votes

Hi AllI am pulling the little hair i have left on my scalp as I can not seem to telnet my webserver publicy on port 80 although I believe i have set it up properly in ios.here are the debug nat statements:00:47:27: NAT: o: tcp (x.x.250.234, 59591) ->...

dborg by Level 1
  • 524 Views
  • 3 replies
  • 0 Helpful votes

I have a Cisco 1841 connected to a DSL modem for its WAN link. The service provider gives us a static IP address by having us send a DHCP request and they allocate it statically based on the MAC. This is configured and working.The service provider of...

GeoffHart by Level 1
  • 311 Views
  • 1 replies
  • 0 Helpful votes

I am trying to do a simple password recovery on a 1801 Fixed ISR. Cisco documentation points me to the common method of hitting the "BREAK" key on startup. This does not seem to work on three different routers. I have tried two PC's as well and still...

I work in a retail environment. Each of our stores has two PVC's. One to router A and router B. My question is can I put all 4 subinterfaces (2 on store router, 1 each on router A/B) on the same subnet (like a 255.255.255.248 for example). what do...

boshardy1 by Level 1
  • 552 Views
  • 3 replies
  • 0 Helpful votes

say we have disabled MLPPP fragmentation in the multilink group which is of 3xE1s, in case the round trip delay of the one link is more than the other two, will a out-of-order packet problem occur, or all the MLPPP frames are sent with seq no.Thanks ...

amie71 by Level 1
  • 318 Views
  • 1 replies
  • 0 Helpful votes

I will appreciate your input regarding the ATM framing for T-3 for different cisco routers. For e.g. if i have a Customer Edge router can i set the ATM-Framing for c-bit manually or it just allows you to have an "auto" settings. Also which router's (...

We have 4 separate sites, each site has an edge switch with VLAN 1 connected round the sites via 100mbps connections forming a loop (or square in this case), the last site was only connected a few weeks ago. The other day I had problem connecting to ...

recyclist by Level 1
  • 705 Views
  • 5 replies
  • 0 Helpful votes

Hello, Can you utilize the backup interface feature for subinterfaces that are on the same physical interface?Example:serial 0.1 ---> PVC #1serial 0.2 ---> PVC #2 (backup interface for serial0.1)It is my understanding that the physical interface itse...

dtecco by Level 1
  • 709 Views
  • 6 replies
  • 0 Helpful votes

Hi all,I am having the following doubt in Redistributing static routes into BGP . Consider eBGP between R2 and R3.Configurations are :R2 configs :hostname R2ip route 150.1.1.0/24 10.1.1.20router bgp 100 redistribute static neighbor 40.1.1.30 remote...