Hi all,I apply QOS setting in the GRE tunnel, it is normal after i apply the QOS setting Three day later, We have many packet loss of ping 8.8.8.8. We got the error in the router. Please find the below message. The error messageJan 7 11:49:36.193: %L...
Forum Posts
Hello Regards to the command "show ip nat statistics" on an ASR1000. The increment of the counters "In-to-out drops", "Out-to-in drops" and "Port block alloc fail:" are refered to a PAT problems? Or just are packets that don´t need to do nat? This...
Resolved! Setting up WAN Access in Cisco 891F
Hi Everyone, I have a Cisco 891F router that I got second-hand for a lab environment that I am trying to setup. I managed to reset it, gain access to the router, and set some things up, but I am unable to get access to the internet from a computer co...
Hi all,I have a question similar to another I asked previously. I'm wondering what strategy would be used to simulate traffic flowing through an ISP router in packet tracer. Both ASAs have dynamic NAT enabled and can ping each other as they have rout...
I have a network i'm practicing on consisting of an ASA, two routers, two switches, and two hosts. I have configured dynamic NAT on the ASA. I can ping PC1 from R1 but if I try to ping PC1 from PC0 it doesn't go through. While looking at the simula...
Hi everyone,Wish you have anice day!I have a lab as picture below. The lab request R5 just learn 1 row route 10.0.0.0/8 from ABR R1. How can I summary on R1 all subnets 10.0.0.0/8 behind it, I try configure on R1(config-router)#area 0 range 10.0.0.0 ...
Resolved! Defaut route and track
Hi guys need to check my sanity - I'm pretty sure i have this right I've got quite a simple set up R4 has 2 default routes using the track command to favour 192.168.0.1 as the default gateway : interface FastEthernet0/0ip address 192.168.0.2 ...
Resolved! ASR 903 Error log
Hi I have an ASR 903 RSP3. when it tries to boot up, the following log appears on the console: Image loadedBoot image size = 518430927 (0x1ee6a0cf) bytesI2C Bus busy, please check the BP IDPROMget_mac_addr: Couldn't find a valid macaddrI2C Bus busy...
Resolved! PBR and VTI IPSEC
Hi we are trying to configure PBR with VTI as next-hop interface or ip address, but with no luck. we see that traffic is matching the PBR and ACL and indeed the traffic is returned according to the statistics of show crypto ipse sa peer x.x.x.x but...
Resolved! risk posed
Explain the set of risks you for see. Write in detail which risks could you mitigate, and which risks will be left in the system
I have the current script written to get me into the router."plink.exe" -ssh username@host -pw password < "input.txt"The problem is once I am in the router I need it to enable and then enter another password in before I can execute commands. When I r...
We have a network generally outlined like this:Site 1Sonicwall NSA2650|Cisco 9200L||fiber connection via 10GB GBIC's.|| Site 2Cisco 9200L|Sonicwall TZ600 The Two Sonicwalls are connected to their ISP's on each side.Each is the default gateway for the...
We have purchased a router having model Cisco 2821 from a supplier and we have asked them to provide cisco login ID so that we can access cisco resources against the purchasing of Cisco 2821 router. The supplier told , you can also register the cisco...
I am facing issues in connecting a pc from outside interface to dmz interface on cisco 5505 asa firewall. The icmp ping is successfull from outside pc to dmz server but failed to establish any tcp connection.ASA Version 8.4(2)!hostname ciscoasanames!...
Hi All. I have 2 catalyst switches running mstp and connected to core 6509 also running mstp. The connection is as below SW1 ----- SW2 \ / \ /Core Switch MSS The SW1 & SW2 have vlan 60,61 & 250 and Core Switch did not have v...
