There's an error in startup where it's on a loop of boxes. Before this, I was in the middle of pending process then I mistyped and interrupted it, it asked me to continue but instead I restarted the router and this happen. Lmk if someone has encounte...
Forum Posts
hello to everyone i have trouble with this topology > i used between sw-1 and sw-3 dot1q protocol and between sw-2 and sw-4 i used dot1q but between sw-3 and sw-4 i used ISL and i have two vlan 99 and 199 while ISL isnt able to tag vlan id it sen...
help me create an access list in the home router:-only Pc1 to access the finance server-webserver to be accessed by all pc-database server to be accessed by all pc except PC1
So I have a PTP S2S IPSEC tunnel created for a location I was able to get the connection up I can ping all the Endpoints in the route okay on both sides. However I noticed connecting to RDP or doing SMB it was SLLLOOOOOW. Or just disconnected due to ...
From LAN port Cisco router series 4200, I m getting only 32 mpbs even though it is gigabit port. And upon replacing it with TP link router I m getting 90 Mbps. Help me!!!
Resolved! ASR-9000V-DC-E cable part number
Hello, I have a customer with a couple ASR-9000V-DC-E units and they've lost their cables. Does anyone know the part number for ordering for these units? I don't think it's this A9KV2-DC-CBL-E because these are not V2s. Thank you for your help!
Hi I have been trying connecting a router B from a router A via Async to console port. It's not working. Have configured async port and line port as well. But whenever I telnet the line, it takes me to the Cisco 8200 A (terminal server) itself. It's ...
Resolved! CISCO ROUTER AS STATELES FIREWALL
Hello, I am new in the security and learning about the state full and stateless firewalls. I understand that with stateful firewalls, any outbound traffic is generally whitelisted so it can return by default since the firewall is aware of the sta...
Resolved! VRRP VIP and the physical interface IP
Hello, everyone. I am studying VRRP at the moment and I found out that you can configure the VIP to be the same as one of your interface IPs (which wasn't possible in HSRP). I have two questions about this. 1. If the VRRP router owns the virtual IP,...
We have unknown protocol and output drops to Meraki, cdp is enabled but not lldp. Does any have face this kind of issue?GigabitEthernet0/0/x is up, line protocol is upHardware is 24xGE-4x10GE-FIXED, address is 706d.155c.af9x (bia 706d.155c.af9x)Descr...
our Kiosks team are saying the below jitter is the cause of their system issues that include payments. could it be or it is just the classic network fault thing? Pinging X.X.X.X with 32 bytes of data:Reply from X.X.X.X: bytes=32 time=26ms TTL=124Repl...
I inherited a network with a Cisco 8200L with a P-LTEA-EA Module and a Sierra Wireless EM7455 cellular modem. I am new to LTE/cellular configuration on Cisco routers. I am told how this configuration is supposed to work is that you send an SMS mess...
Resolved! Cisco 3560 Dual ISP Failover help
hi experts! question for home lab setup is it possible to have the setup of when isp1 goes down pc1 on the diagram goes to isp2 on a different vlan and vice versa. Currently they work on their own pc1 gets internet of isp1 . pc2 gets internet from is...
Resolved! Syslog over TLS NCS540X
Hello, TCP port 6514 is the default port for syslog over TLS, i want change this port's value, but i don't find anything for this Have you idéa?
Hey hi,We are looking to replace the 2960s and 2950 switches, which would be the best replacement?
