Please help me out. IP master : 192.168.25.0/23.With following host requirements :HRM = 199IT = 20FINANCE = 41OPERATIONS = 17SALES = 2SUPPLY CHAIN = 13 what is the IP Adress, First Host, Last Host, and Broadcast IP for each department? (Using CIDR me...
Forum Posts
I have done with my DMVPN Lab Phase I Configuration. I have found that Hub is able to learn routes of both spokes. But spoke is not able to learn route of other spoke(LAN).EIGRP enabled for Hub and spokes NBMA and LAN Networks.Static default route i...
Resolved! Redistribute BGP into EIGRP
Hi, Im new in networking. Im doing a lab where Im trying to see bgp loopback ip ( i.e 3.3.3.3 ) in eigrp. I m not able see. But while im adding a static route at Null 0 and adding 3.3.3.3 in eigrp network statement then its showing. in R2 ( whoic...
Hey There, So I have created another ROAS setup (using packet tracerr) but this time I have a router connected to a 3560 SW, that is in turn connected to a 2960 SW. I have created the sub-IF on the router and have set up the links between devices as...
A company has been allocated the address range 187.11.0.0 to 187.27.255.255 What is the network (supernet) address and what is the (supernet) mask? (Hint: You might want to convert them into binary and calculate the common bits)
Resolved! SG350 - Inter-VLAN communication
Dear all,I have recently decided to upgrade my home network infrastructure and chose CISCO gear to do so. My setup is as follows:------------------- ------------------- ------------------------- |AVM FritzBox 7490|------------>...
Hi,I need to configure a switch SG250-18 L3 to routing traffic from VLANs.I have defined 3 VLAN (ID 1, 2 and 11)The VLAN 1 is for a closed management networks where are all PCThe VLAN 11 is only for a closed big data transfer (Vmotion, Backups and ot...
Hi All, Python script to get cisco device model, IOS version on to excel and list of local login users. Python script to create local username and password with certain privilege's and then delete any other users Thanks in advance.
Hi All, We have a PIM domain that is running PIM-SPARSE mode and it's working fine. We have a customer who needs our multicast feeds. But we cannot allow PIM neighborships between us and the customer.So we decided to enable IGMP Static Join on the cu...
Resolved! ISR4451-X power consumption
Hello all, I'm looking for router's model ISR4451-X power consumption, but I'm not able to find it.I also tried to check the data sheets for this model, but I wasn't successful.Is there anybody who is able to help me please? Thank you!
Hi Guys,This is for sure a dumb question but as I don't know the answer I think I need to ask. I wish there was a "New to networking" or similar section of the forums. Despite having spent some time on Packet Tracer now, I am still finding it somewha...
Hi All, Can anyone pls clear the doubt. Suppose there is a downstream core switch connected to 2 WAN routers (R1 & R2).Switch is getting EIGRP routes from both WAN routers.R1 is advertising better route to Switch than R2.Now suppose, HSRP is configur...
Dear Everybody! How it possible to query the firewall blocked A:P->A:P connections on RV130? We use RV130 for sensor network as firewall.This mean continuous and high (small packet) traffic on many TCP connection. During sometimes the firewall block...
Resolved! Cannot ping access layer switch, why?
The file attached is our overall configuration. May i know why is it my PC can ping the other PC, distribution layer switch as well as the Router gateway but just couldn't ping both of the access layer switch?The switch which could not be ping is sw...
We are running an multiple ipsec tunnel on ASA firewall-1 the design is simple we have multiple inside interface and single outside interface(vpn tunnel is built on outside interface) so whenever we need to allow some traffic we apply ACL on inside i...
