Hi Guys can u pls help me at the below thread https://community.cisco.com/t5/networking-blogs/sd-wan-controller-on-premise-deployment/ba-p/4176351 thanks
Forum Posts
The Cell0 interface is working fine, pinging 8.8.8.8 without any problems.but from vlan1 network 192.168.1.0, getting dhcp with ip address and dns but cannot reach 8.8.8.8 from connected PC Vlan1 kindly help me ...the configurations below !ip cef!!!!...
This is basic MPLS-VPN LaB i am practicing on GNS3. topology Diagram is attached.I am unable to ping from PE(R-2) to PE(R-4). routes are showing in neighbor table of BGP but not in routing table.Please help. I am attaching config files of PE(R2) , PE...
Hi im new with this networking thing and really need help on how to sort out the problem with our network setupwe have this two devices and been using for more than 10 years without problemCisco 1841 Router (under vlan 50 - 10.130.50.4)Cisco Catalyst...
Hey everyone, I have a network with inter vlan multilayer switch.I configured dhcp on both M Switches.The problem is that my clients use the MS2 for dhcp and not the MS1, when i shutdown the ports of MS2 , they will use MS1 as redundant Dhcp server, ...
Hi,I have the following situation described in this article: "https://www.bytesofcloud.net/2018/10/ospf-vpc" show ip ospf neighbors vlan 387OSPF Process ID 1 VRF defaultTotal number of neighbors: 4Neighbor ID Pri State Up Time Address Interface10.25...
Hello, does anybody know if Cisco C1000 Series support the FDPS (Frequency Dependent Pilot Sequence, G993.5 G.vectoring)?
1. Check if Vectoring is enabledIOS router shows the training mode as G993.2 even though the line is trained with full vectoring and this documented with the below cosmetic Bug:Bug Link: https://bst.cloudapps.cisco.com/bugsearch/bug/CSCuw72999Recomme...
Hello everyone, we have an ASR-1002 up and running as pppoe server with radius auth, more than 500 subscriber sessions.We'd like to know if we can see mac address and some info about pppoe clients (brand and model of clients routers and so on)with sh...
Hi, I want configure Dual ISP on ASA 5506-X (based license). I tried this procedure (ASDM mode) http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/118962-configure-asa-00.html But it does not work. When ...
Hi everyone , I would like to talk about qos with vrf-lite and the possibility of interaction between them.I was wondering if it would be possible to classify traffic based on source ip with overlapping subnets each one belonging to a different vrf c...
Resolved! default routes
Hi every one , I had some issues in my lab network, actually all my traffics users go to the internet throught the ISP-01 by defaut route like this : ip route 0.0.0.0 0.0.0.0 a.a.a.a, now i want to make another route to internet by another ISP-02 con...
HI!I want to know about different redundancy how fail over works in Cisco 6509-E with 2 Sup-720-3B supervisors? Do I need to connect those 2 supervisors active and standby via Ethernet cable for fail over or it some kind of internal process?RPR and S...
We have a requirement to handle 15 multicast streams. Currently, we configured PIM configurations on our existing backbone. So, I need to find a suitable router to cater to 15 multicast streams. I selected the Cisco 3925 and Cisco 2951 router. Please...
Hello All, I encounter a problem regarding openvpn connection via ISR router. Simply put, there is one device resided in the LAN side of ISR Router which would be acted as openvpn client. This client is supposed to initiate and actively establish vpn...
