Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hello guys, I have  a problem sometimes my router reach 99% and  the normal process is 20% so I dont know  why sometimes hight to 99% CPU utilization for five seconds: 99%/64%; one minute: 99%; five minutes: 99%PID Runtime(ms) Invoked uSecs 5Sec 1Min...

Resolved! Network routing

I created a Lo102 interface on router R1 ip address 100.110.102.1 255.255.255.0 to simulate a network behind it. I have a 172.21.1.0 / 24 network from a 701. vlan. I announced the 172.21.1.0 network via OSPF on R17 to R1.# R17 # ospf 100 # routersumm...

LincolnR by Level 1
  • 1859 Views
  • 8 replies
  • 0 Helpful votes

Hi, I purchased a second-hand Cisco 867VAE (IP-Based version) router and was exploring its configuration when I noticed that after assigning "Ethernet 0" with an IP address, I couldn't ping my desktop (same subnet of course). However, I could pink my...

Rolitto by Level 1
  • 1533 Views
  • 2 replies
  • 0 Helpful votes

Hi specialists,When starting-up firepower & face to "locally config", what will occur if I choose "Yes"?Policies-->Network discovery-->Networks-->Add rule   What's the difference between "host" & "user"?What does "generate event" do with a signature?...

Hi all,I need to install IOS XE 16.12.4 on a C1111 router. I see there is a normal version and a version with "ias" in the filename.What is the difference? What version should be installed on a 'standard' setup (a bit of routing, switching, 4G/LTE, V...

matty-boy by Level 1
  • 5948 Views
  • 3 replies
  • 0 Helpful votes

HiIn the following topology, what would be the best way to ensure the spokes prefer one HUB router for all routes over this iBGP route-reflector setup?HUB router config*************************************************neighbor ELAN-IBGP-PEER peer-grou...

Hi, I have internet access with my router. FE 0/1 is WAN port setup for PPPOEFE 0/0 is standard port. Network setup - VDSL modem -- router 1 (1841) switch(2960) -- PC.Router 2 which can also ping the main router 192.168.1.1Summary Router 2 and PC do ...

We had a Cisco stacked 3750 as our core/distribution in a collapsed model and we replace it with 2 Cisco Nexus with vPC/HSRP/OSPF/static ip route summarization taking over the core/distribution role and also hosting our VMWare ESXi and SAN. However w...

i have two routers ra and rb with HSRP between them i have configured dhcp exclusion addresses but i am getting ip conflict ERROR MASSEGES BELOW detailsJul 15 2020 15:05:57.883 UAE: %DHCPD-4-PING_CONFLICT: DHCP address conflict: server pinged 10.114....

AHMADJ by Level 1
  • 1793 Views
  • 8 replies
  • 0 Helpful votes

Hello,Can anyone explain the value of using a static null0 route with an administrative distance?  We use these to seed the BGP table for /16 networks at various locations and I have noticed that some of them are configured with an administrative dis...

i Dear FriendsWe have several ASR 1002-x with IOS version: asr1002x-universalk9.16.06.07.SPAWe use these ASRs for PPPoE termination. Around 18K session per router.Each router has 16GB of RAM. Recently I noticed The memory usage of each router is incr...

Hello All,I am try to Connect my Cisco C1111-8PLTEEAWB to my Cisco 4321. I wan to use the C1111 Console-RJ45 or USB3 port to make a connection to the 4321 via its AUX port using reverse-telnet. Is this possible? I havent found a way. Creating this co...