hello everyone,in my topology., my client has an ip adress 192.168.1.1. remote site server has 10.251.67.44. I succeed the access the server with a different source ip address 172.29.103.1 via ipsec tunnel. by the static nat I am changing the source ...
I'm doing a project where I have a Winradius server on two inside servers, with the two test accounts:Username: User1 Password: examplepwUsername: User2 Password: examplepw2 Trying to figure out the commands needed on the ASA for the following things...
Hello guys, i'am learning some courses about QoS for a project and i still dont understand the difference between the priority given to classes (AF4 or AF3 for example) and the bandwidth given with CB-WFQ on the egress. A traffic that i gived for exa...
Can I enable BFD for VLAN interface as I am not seeing the BFD command under VLAN interface as following?CDCCORCSW003(config)#int vl202CDCCORCSW003(config-if)#CDCCORCSW003(config-if)#bfd ?% Unrecognized commandCDCCORCSW003(config-if)#int gi8/1CDCCORC...
Hi,i’am new in this forum and pretty new to Cisco network devices and configuring them (I just started learning for CCENT1) :-) I need to configure a Cisco Router (Cisco 892) which ís connected to two ISP’s (no Loadbalancing) with two networks. For e...
Greetings, i have a hub and spoke IPSEC/GRE configuration connecting together 5 routers. I can ping from spoke to spoke when connected to each spoke router but if i add the inside interface as the source address i cant ping between spokes.I think it...
Good afternoon with everyone, the consultation is up to one hundred point very basic. I have a platform of Routers ISR2 3945, and also ISR1 2825 and 2811, now I have added a Router 4400, in all routers I can get backup of the configurations, via TFTP...
I have a Cisco 3850. I have read the discussions on whether or not they do NAT. It appears people have got them to do so. I am needing mine to nat between 192.168.125.x(inside) and 10.10.9.x.(outside). I am needing to be able to hit a device on t...
Hi All, Is it possible to access the internet connection through a VPN? Router B(WAN2) connects to Router A(WAN2) via ethernet cable with a VPN tunnel. router A(WAN1) connects to ISP fiber broadband. Router B WAN1 is not connected to any ISP. Will ...
Why does the Dialer interface show LCP as closed, but on the Virtual-Access interface LCP shows up as open?Also, is it normal for the NCPs to only show up under the Virtual-Access interface? What is the reasoning for this? sh int di1Dialer1 is up, li...
Hola, actualmente tengo la necesidad de configurar la red particionada en 3 redes mediante VLAN,s mediante en CISCO SG300-10 y la configuración actual que necesitaría es: VLAN2 red de 2 impresoras. Sin acceso a internet VLAN3 red de TV con acceso a ...
Hello all,I've looked around and there seem to be very little info when configuring this, but apologies if I missed this, and this is also my first post so my bad if this is explained poorly but my goal is this:- bt adsl terminating to 4321 with NIM-...
Hello Cisco community,I was wondering how can I use VPN from phone?I did the configuration but I don't know how to test or whether the configuration is correct or not,find the attached Zip fileplease help Thanks in advance
Hi Can anyone explain why is this route installed in ipv6 RIB?L FF00::/8 [0/0] via Null0, receive ThanksSiva
Hello,I was studying on bgp performance and I came across "bgp fast-external-fallover" and BFD. I am confused because both achieve the exact same thing. Could anyone please let me know when we should "bgp fast-external-fallover" over BFD or vice vers...
